Оценок - 2, средний балл: 4.5 ( )

Производитель: Genie Размер: 641.13 kb Название файла: 82828.pdf Язык инструкции:

If the light stays red, tag and remove the machine from service. OPERATING INSTRUCTIONS Indicator Light Flashing Red If the indicator light is flashing red, the platform is overloaded and no functions will operate. An alarm will sound at the platform controls. Remove weight from the platform. Push in and pull out the red Emergency Stop button to reset the system. If the platform is still overloaded, the light will continue to flash. To Extend and Retract Platform 1 Lift the platform extension lock handle to the horizontal position. 2 Push the platform extension lock handle to extend the platform to the desired position. Do not stand on the platform extension while trying to extend it. 3 Lower the platform extension lock handle. Auxiliary Lowering At the Ground Controls Push and hold the lift function enable button and activate the down function. In the event of a power failure, use the backup auxiliary lowering function. At the Platform Controls Push and hold the lift function enable button and activate the up/down rocker switch in the down direction. PartNo.82828 Genie GS-3384 & GS-3390 & GS-4390 & GS-5390 Operator's Manual Second Edition • Third Printing OPERATING INSTRUCTIONS Operation From Ground with Controller Maintain safe distances between operator, machine and fixed objects. Be aware of the direction the machine will travel when using the controller. Outrigger Operation (if equipped) 1 Position the machine below the desired work area. Note: The engine must be running for the outriggers to operate. 2 Push and hold the auto level button. 3 Activate the up/down rocker switch in the down direction. The outriggers will extend and level the machine. A beep will sound when the machine is level. The indicator light on the lift function enable button will turn red when one but not all outriggers are down. All drive and lift functions are disabled. The light turns green on the lift function enable button and on the individual outrigger buttons when all the outriggers are in firm contact with the ground. The drive function is disabled while the outriggers are down. To control individual outriggers 1 Push and hold one or more outrigger buttons. 2 Activate the outrigger up/down rocker switch in the desired direction to level the machine. Fall Protection Personal fall protection equipment (PFPE) is not required when operating this machine. If PFPE is required by job site or employer rules, the following shall apply: All PFPE must comply with applicable governmental regulations and must be inspected and used in accordance with the manufacturer’s instructions. After Each Use 1 Select a safe parking location—firm level surface, clear of obstructions and traffic. 2 Lower the platform. 3 Turn the key switch to the off position and remove the key to secure from unauthorized use. 4 Chock the wheels. Genie GS-3384 & GS-3390 & GS-4390 & GS-5390 PartNo.82828 Second Edition • Third Printing Operator's Manual Transport and Lifting Instructions Observe and Obey: Common sense and planning must be applied to control the movement of the machine when lifting it with a crane. The transport vehicle must be parked on a level surface. The transport vehicle must be secured to prevent rolling while the machine is being loaded. Be sure the vehicle capacity, loading surfaces and chains or straps are sufficient to withstand the machine weight. See the serial plate for the machine weight. The machine must be on a level surface or secured before releasing the brakes. Free-wheel Configuration for Winching Chock the wheels to prevent the machine from rolling. 2WD models: Release the non-steer wheel brakes by turning over the torque hub disconnect caps (see below). 4WD models: Release the wheel brakes by turning over all four torque hub disconnect caps (see below). Be sure the winch line is properly secured to the drive chassis tie points and the path is clear of all obstructions. Reverse the procedures described to re-engage the brakes. Note: The pump free-wheel valve should always remain closed. Disengage Position Engage Position PartNo.82828 Genie GS-3384 & GS-3390 & GS-4390 & GS-5390 26 Genie GS-3384 & GS-3390 & GS-4390 & GS-5390 Part No. 82828 Operator's Manual Second Edition • Third Printing Securing to Truck or Trailer for Transit Always chock the machine wheels in preparation for transport. Retract and secure the extension deck(s). Use the tie-down points on the chassis for anchoring down to the transport surface. Use a minimum of four chains or straps. Use chains or straps of ample load capacity. Turn the key switch to the off position and remove the key before transporting. Inspect the entire machine for loose or unsecured items. If the railings have been folded down, secure them with straps before transporting. TRANSPORT AND LIFTI NG INSTRUCTIONS Part No. 82828 Genie GS-3384 & GS-3390 & GS-4390 & GS-5390 27 Second Edition • Third Printing Operator's Manual Observe and Obey: Only qualified riggers should rig and lift the machine. Be...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: