Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Note: The controller can be fitted to suit either right or left-handed users. Please contact your provider for further assistance. 4/27/2006 10 The Joystick Controller (VR2) Shoprider HD (888 WHD) 1. On-Off Button: This button turns the joystick controller (hereinafter referred to as VR2) on and off. Do not use this button to stop the power chair, except in an emergency 2. Battery Gauge: This is a 10segment display, which indicates if the VR2 is switched on and gives the state of charge of the battery. Additionally, any faults in the Powerchair electrical system are also indicated by this display. Refer to Table 1 for more details. 3. Maximum Speed Indicator: This is a 5-segment display, which indicates the maximum speed setting selected. 4. Horn Button: This button operates the Powerchair’s horn. 5. Speed Decrease Button: This Button Increases the maximum speed. 1 2 4 3 7 6 5 8 Figure 4 6. Speed Increase Button: This Button Increases the maximum speed. 7. Joystick: This controls the speed and direction of the Powerchair. Push the joystick in the direction you want to go. The further you push it, the faster the speed will be. Releasing the joystick will automatically engage the brakes and stop the Powerchair. 8. Charging Port: This is the only charging port for the Shoprider HD. When using this charging port only plug into this port with the qualified Shoprider charger certified by the original manufacturer of the Powerchair. This port should not be used as a power supply for any other electrical devices. Doing either of these as stated above will void the warranty of the Powerchair. Note: The controller can be fitted to suit either right or left-handed users. Please contact your provider for further assistance. 4/27/2006 11 LOCK MODE: The VSI controller can be locked to prevent unauthorized use. The locking method is achieved through a sequence of key presses and joystick movements, as detailed below. Note; The joystick controller may or may not be programmed for the lock mode function. Please contact your provider for further information. To lock Powerchair controller: • While the controller is switched on, depress and hold the on/off button. • After 1 second the controller will bleep. Now release the on/off button. • Push the joystick forward until the controller bleeps. • Push the joystick in reverse until the controller bleeps. • Release the joystick, there will be a long bleep. • The Powerchair controller is now locked. To unlock the Powerchair controller: • Use the on/off button to switch the controller on. The maximum speed/profile indicator will be rippling up and down. • Push the joystick forward until the controller bleeps. • Push the joystick in reverse until the controller bleeps. • Release the joystick, there will be a long bleep. • The Powerchair is now unlocked. SLEEP MODE: If the controller is left on and not used for more than ten minutes, the controller will automatically “go to sleep”. This is recognized by a slow intermittent flash of the battery indicator lights. Simply turn the controller off and back on to reset. Always leave the chair in drive mode. The freewheel option is there only to allow the chair to be pushed manually when the need arises (i.e., to store or push unit out of a tight space). Following the sticker picture put each lever in the direction of the person sitting down driving the chair. The Powerchair will not function while the drive mechanism is disengaged (in freewheel). In addition, the VSI will flash a fault code and beep steadily if turned on. Refer to Table 1 for more details. 4/27/2006 12 Both left and right sides must be in drive mode for power chair to operate. Otherwise the Powerchair will flash fault code of 9 lights and will not operate (VSI only). For the HD; if one side is in drive mode & the other is in freewheel, the powerchair will spin in circles. Shoprider HD Drive/Freewheel Mechanism The drive/freewheel levers are found toward the rear of the Powerchair, one on top left and one bottom right. These levers will allow you to disengage the drive mechanism and push the Powerchair while in freewheel mode. (FIG. 5) Shoprider WS Drive/Freewheel Mechanism The drive/freewheel levers are found toward the front of the Powerchair, one on each side, located at the end of each motor. These levers will allow you to disengage the drive mechanism and push the Powerchair while in freewheel mode. (FIG. 6) Figure 5 Free Wheel Levers Figure 6 Free Wheel Lever, NOTE: There is another lever on opposite side, same location 4/27/2006 13 Adjustable Arm, Seat Assemblies and Footplate Assemblies 1 4 2 5 6 3 Figure 7 1. Vinyl armpad 2. Height adjustment bolt, allows for the height of the armpad to be adjusted to fit the users needs. 3. Pivot base for the front of the armpad. Acts as a base allowing for easy flip up release for the armpad. 4. Seat height adjustment pins. Allow for the height of the seat to be adjusted to fit the user’s needs. (4 pins total) 5. Height adjustment...
Эта инструкция также подходит к моделям:Инвалидные коляски - WS 888WS (547.87 kb)