Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
Loosening the arm rest hand knob allows the armrest width to be adjusted or arm rest to be removed. Once the desired positions of the arm rests are set, tighten the hand knobs by turning clockwise to lock the arm rests into place. Armrest Adjustments (Fig 6) The arm rests may be pulled up and out of the Figure 6 way for sideways transfer. Pull arm rest up and back. The arm rest angle may be adjusted by turning the adjustment screw either clockwise or counterclockwise depending on the desired angle. Armrest tightening knob 7/8/2009SE 8 SCOOTER TILLER CONTROLS (FIG 7) Speed Controls The speed control allows you to set a speed between slow (turtle) and fast (rabbit). Battery Level Indicator Gauge Where the needle sits, shows the amount of charge left in your batteries. The amount of charge will only show at its true level when the scooter is in drive. Always charge the batteries completely before beginning out on any journey. Caution – Do not allow the gauge needle to go down completely as complete discharge of the batteries could cause irreversible battery damage. Horn A yellow button on top of the tiller operates the horn. Thumb Lever Controls The left thumb lever controls the reverse and the right thumb lever controls the forward motion. The amount of pressure applied to each lever will determine the speed the scooter travels at up to the speed selected. Release the thumb lever and the scooter will automatically come to a stop as the electromagnetic brake is applied to the motor. On/Off Key Switch Insert the key into the key switch located on top of the tiller. Turn the key and the battery gauge needle will move. There may be a slight delay before the thumb lever control can be operated, while the main controller checks the circuits. Electromagnetic Brake The brake is automatically operated when the thumb control levers are pressed or released. There is a slight delay when the scooter accelerates and decelerates; this allows the scooter to Start 8 smoothly and come to a smooth stop. Battery Level Indicator Gauge Speed Control Dial On/Off Key Switch Horn Button Thumb Lever Control (Forward) Thumb Lever Control (Reverse) Figure 7 7/8/2009SE 9 DRIVE/FREEWHEEL OPERATION (FIG 8) The drive/freewheel lever (yellow ball handle) is located under the seat at the right rear of unit. This lever allows you to disengage the drive mechanism and push the scooter while in freewheel mode. To disengage the drive mechanism (neutral), move the lever forward (the scooter can now be pushed). To re-engage the drive mechanism (drive), move the lever backward (now the unit may be driven). Note: The scooter will not operate while the drive/freewheel lever is in the neutral position (forward). The scooter must be turned off, lever moved backward (drive position) and then turned on in order to reset the circuits. WARNING! Always re-engage the free wheeling device after use. Failure to do so may result in injury. Anti-tip wheels The anti-tip wheels are located at the rear of the scooter frame (Fig 8). The scooter should not be used unless the anti-tipping wheels are in place. Shoprider® is not responsible for damage or injury incurred due to improper or misuse of the scooter. Scooter serial number The scooter serial number is located on the seat post and consists of a combination of 13 numbers and letters. Shoprider recommends that you write the serial number down on the back of this manual for future reference. Refer to Fig 5. Figure 8 Freewheel Lever Anti-tip wheels Frame Detach Lever 7/8/2009SE 10 STARTING TO DRIVE YOUR SCOOTER First Time Use Prior to using your Start 8 Portable scooter for the first time, you must charge the batteries fully (refer to Battery Charging Procedures). Charging may take up to 12 hours. Charging the batteries completely prior to first time use will benefit battery efficiency. Failure to do so may cause permanent damage. Getting Start 8ed • Select a level area with plenty of space. • Mount the scooter by pushing the arm upward out of the way and sliding onto the seat or swivel the seat around to mount. Use the arm rest for support if necessary. • Adjust the tiller and seat as previously described. Start 8ing Scooter Movement • Ensure that you are seated in a comfortable position. • Turn the key to the on position. • Your speed setting should be on or near the turtle (slow). • Push your right thumb lever (yellow) and the scooter will move forward slowly. The harder you push, the faster the scooter goes but will only reach the speed level that has been selected. • Release the lever and the scooter will slowly come to a stop as the magnetic brake automatically engages. Steering Steering the scooter is light and easy. When Starting off ensure that you give a wide clearance when turning so that the rear wheels clear any obstacle that you are passing. When steering through limited spaces such as a doorway or when turning around, turn the tiller handles where you want to go and apply power gently. The scooter will...