Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
You should adjust the damper based on the fire’s appearance. A low, reddish, dirty fire can be improved by pulling the damper out slightly. A “blow torch” fire can be improved by pushing the damper in a bit. As a general rule, on lower feed rate settings, the damper should be in farther. On higher feed rates, the damper should be more open. Through trial and error, you will find the best setting. Consult your dealer if you need help. NOTE: On “1”, damper should be out approximately 1/8” to .”. If damper is out too far, it can cause the fire to go out. REFUELING We recommend that you not let the hopper drop below . full. KEEP HOPPER LID CLOSED AT ALL TIMES EXCEPT WHEN REFILLING. DO NOT OVERFILL HOPPER. BRECKWELL MAINTENANCE TOOL A tool has been provided to help with the following functions: FIGURE 23 a. Stirring pellets in hopper – unlike liquids in a tank, pellets do not drain evenly into the auger. Bridging across the opening can occur. Pellets can hang up on the sides of the hopper. Occasionally “stirring” the hopper can help. NOTE: To help prevent bridging of pellets, common wax paper can be rubbed on the sidewalls and bottom of the hopper. b. Cleaning heat exchanger tubes – see instructions in “CLEANING”. c. Scrape ashes from burnpot. SHUTDOWN PROCEDURE Turning your Breckwell stove off is a matter of pressing the “Power” control panel switch. The red light will go out. The blowers will continue to operate until internal firebox temperatures have fallen to a preset level. SAFETY FEATURES a. Your stove is equipped with a resettable high temperature thermodisc. This disc has a reset button on its backside. This safety switch has two functions. 1. To recognize an overheat situation in the stove and shut down the fuel feed or auger system. 2. To recognize an internal control board failure and shut down the fuel feed or auger system. NOTE: Like a circuit breaker, once tripped, the reset button will have to be pushed before restarting your stove. The manufacturer recommends that you call your dealer if this occurs as this may indicate a more serious problem. A service call may be required. b. In case of a malfunctioning convection blower, a high-temperature thermodisc will automatically shut down the auger, preventing the stove from overheating. NOTE: Thermodisc must be reset after this occurs. c. If the combustion blower fails, an air pressure switch will automatically shut down the auger. NOTE: Opening the stove door for more than 30 seconds during operation will cause enough pressure change to activate the air switch, shutting the fuel feed off. Close the door and press “On/Off” button to continue operation of your stove. THERMOSTAT INSTALLATION 17 OPTIONAL THERMOSTAT A thermostat may help you maintain a constant house temperature automatically. A millivolt thermostat is required. A fixed wall mount or Breckwell’s hand held model can be used. The control panel can be set up two ways to operate your stove in thermostat mode. THERMOSTAT INSTALLATION • A MILLIVOLT THERMOSTAT IS REQUIRED. • Unplug stove from power outlet. • Remove control board from stove. • The two thermostat wires connect to the terminal block on the lower right side of the back of the control board. (See figure 24) • Loosen the two screws. • Make sure to remove the jumper wire from the terminal block prior to connecting the wires. • Insert the wires in the terminal side and tighten the two screws. SHUNTS To change from the factory setting all that is required is to move one shunt. There is one shunt and two sets of pins on the rear upper left part of the control board. J8 or the two upper shunt and pins should be disregarded as it is for factory testing of the control board. J9 is the lower shunt and pins. • When the J9 shunt is over one pin, or off both pins, the digital control board is in high/low thermostat mode. THIS IS THE FACTORY SETTING FOR THE DIGITAL CONTROL BOARD. • When the shunt is over both pins the digital control board is in ON/OFF thermostat mode. MODES HIGH/LOW THERMOSTAT MODE • When engaged in this mode the stove will automatically switch between two settings. When warm enough, it will switch to the #1 or low setting. The room air blower will also slow to its lowest speed. • The Heat Level Advance setting on the bar graph will stay where it was initially set. When the house cools below the thermostat setting, the stove will switch to the feed rate of the heat level advance setting. ON/OFF THERMOSTAT MODE • In this mode when the home is warm enough the stove will shut off. The fans will continue to run until the stove cools. • When the home cools below the thermostat setting, the stove will automatically restart and run at the last feed rate setting. NOTE: When in “high/low” or “on/off” thermostat mode – • Do not operate the stove higher than the #3 setting. • Set damper control rod approximately .” out. This will vary depending on elevation and weather conditions. • When stove is hooked up to a thermostat it will not opera...
Эта инструкция также подходит к моделям:Газовые нагреватели - ECONOMY P22FSL (742.9 kb)
Газовые нагреватели - ECONOMY P22I (742.9 kb)