Войти:
Оценок - 3, средний балл: 4 ( )

Инструкция по эксплуатации Desa, модель 75-200

Производитель: Desa
Размер: 1.52 mb
Название файла:
Язык инструкции:enesfr
Перейти к скачиванию



Фрагмент инструкции


This provides fuel to the heater. The Ignition System: The piezo ignitor lights the pilot. TheAutomatic Control System: This system causes the heater to shut down if the flame goes out. PRODUCT IDENTIFICATION Outer Shell 80,000 B T U / H R Ignitor Button Ball Valve Safety Pilot Control Knob Valve Figure 1 - 80,000 Btu Model Shown VENTILATION WARNING: Provide at least a 2.5 square foot (0.23 m2) opening of fresh, outside air while running heater. If proper fresh, outside air ventilation is not provided, carbon monoxide poisoning can occur. Provide proper fresh, outside air ventilation before running heater. 113811-01A PROPANE SUPPLY You must provide propane gas and propane tank(s). Use this heater only with a propane vapor withdrawal supply system. See Chapter 5 of the Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/NFPA 58 and/or CAN/CGA B149.2. Your local library or fire department will have this booklet. This heater will operate with a 20-pound (9,07 kg) propane tank. However, you can only operate it in the LOW position during mildly cool weather. At higher heat settings or during colder weather, you must use larger tanks. The amount of propane gas ready for use from propane tanks varies. Two factors decide this amount. 1. The amount of propane gas in tank(s) 2. The temperature of tank(s) The chart below shows the minimum number of 100-pound (45 kg) tanks needed to run the heater. Connect tanks together with a manifold. Average Temperature °F(°C) Number At Tank Location Of Tanks (80,000 Btu models) 20° (-6.7°) to 60° (15,6°) 1 0° (-17,8°) to 20° (-6.7°) 2 (200,000 Btu models) 20° (-6.7°) to 60° (15,6°) 2 0° (-17,8°) to 20° (-6.7°) 3 Less gas is vaporized at lower temperatures. Your local propane gas dealer will help you select the proper supply system. INSTALLATION WARNING: Review and understand the warnings in the SafetyInformationsection,page 2. They are needed to safely operate this heater. Follow all local codes when using this heater. CAUTION: Never ignite and/ or run this heater uhnless the shells are fully extended and locked into position. OUTER SHELL IMPORTANT: When the heater is first removed from carton, the outer shell is in the down position. Protect hands before lifting outer shell. Never grasp bare metal without hand protection. 1. Care must be taken to protect hands during this step. Lift outer shell straight up as shown in Figure 2, until all three clips engage slots in lower shell. Screw holes will line up at this point. 2. Lock clips into place with 3 screws as shown in Figure 2. The heater must not be operated unless the outer shell is properlly extended and fully locked into place. Outer Shell 200,000 BTU/HR Clip in Slot of Lower Shell 3 Screws per Clip Figure 2 - Lifting Outer Shell CONNECTING TO GAS SUPPLY WARNING:Testallgaspiping and connections for leaks after installation or servicing. Never use an open flame to check for a leak. Apply a mixture of liquid soap and water to all joints. Bubbles forming show a leak. Correct all leaks at once. 1. Provide propane supply system (see Propane Supply, page 4). 2. Connect fuel gas fitting on hose/regulator assembly to propane tank(s). Turn fuel gas fitting counterclockwise into threads on tank. Tighten firmly using a wrench. IMPORTANT: Tighten regulator with vent pointing down. Pointing vent down protects regulator from weather damage. 3. Connect hose to the valve inlet. Tighten firmly using a wrench.You must use the regulator supplied with heater even if propane tank has one. 113811-01A INSTALLATION Continued 4. Open propane supply valve on propane tank(s) slowly. Note: If not opened slowly, excess- flow check valve on propane tank may stop gas flow. If this happens, you may hear a click inside the regulator assembly, this is the check valve closing. To reset the excess flow check valve, close propane supply valve and open again slowly. 5. Check all connections for leaks. Apply mixture of liquid soap and water to gas joints. Bubbles forming show a leak that must be corrected. Hose Figure 3 - Regulator Position Propane Tank Propane Supply Valve Regulator POL Fitting Valve Inlet Hose Figure 4 - Hose and Valve Inlet OPERATION WARNING: Review and understand the warnings in the SafetyInformationsection,page 2. They are needed to safely operate this heater. Follow all local codes when using this heater. 2. Fully open the valve on the propane cylinder and wait 15 seconds before proceding to step 3. 3. Depress red button on safety pilot valve admitting gas to the heater. Then push and release the ignitor button until the pilot lights. 4. When the pilot lights, continue to hold the button depressed for 30 seconds, then release. 5. If pilot goes out, wait 5 minutes and repeat the lighting procedure. 6. When the pilot remains lit, open the ball valve (turn knob counterclockwise) to light main Ignitor Button Ball Valve Control Knob burner. Partially close valve to regulate heat output. Safety Pilot...

Эта инструкция также подходит к моделям:
Газовые нагреватели - 30-80 (1.52 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории