Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Ensure the gasket seats evenly as the panel draws shut. Engage the Vee-flange at the bottom of the panel with the latches and close the latches to secure the panel. 4. Reinstall the control compartment door see installation instructions on Page 4 , Reinstalling Control Compartment Door). NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. INSTALL VERMICULITE, VOLCANIC STONE, GLOWING EMBERS AND LOGS 1. Remove the front glass enclosure panel (see Removing Glass Enclosure Panels on this page). 2. Carefully remove the old logs, embers volcanic stone and vermiculite from the fi rebox. Handle logs carefully to prevent breakage. 3. Install Vermiculite - Place some vermiculite on the firebox floor around the burner (the entire bag of vermiculite will NOT be used). See Figures 8 & 9. DO NOT PLACE ANY VERMICULITE ON THE BURNER. Mound up a portion of the vermiculite in front of the burner. 4. Install decorative volcanic stone -Sprinkle the decorative volcanic stone (dark colored) on top of the vermiculite (light colored) in a pleasing pattern (see Figures 8 & 9). 5. Placement of Glowing Embers - Separate the Embers (rockwool) into pieces about the size of a quarter (see Figure 7). Keep the pieces fluffed up, not matted. Distribute these pieces over the surface of the burner, as shown in Figures 8 & 9. Do not use more than is necessary. Ensure that the main burner slots remain uncovered by the ember material. Note: This appliance is provided with enough Glowing Embers for several applications, do not use all that is in a new bag at one time. For best glowing effect, replace the ember material annually. 6. Placement of Logs and Twigs - All logs that have locating notches or slots to help ensure that they are properly positioned. All top logs that rest on lower logs, do so over notches, indents or pins. Proper twig placement is critical to prevent sooting. Twigs should be placed in the gaps between the fl ame peaks and should be positioned so they do not impinge the fl ames. LMDV-3328 & LMDV-3530 - Install as Follows Carefully position the ceramic fiber logs and twigs over the burner as shown in Figure 8. Logs should be placed in the order shown and per the following instructions. 1. Place the rear log (A) as shown. Position the 2 notches on the bottom of the log over the 2 corresponding locating brackets against the back wall of fi rebox. 2. Place the left log (B) as shown. The notch on the bottom of the log should fit over the corresponding locating bracket. 3. Place the right log (E) as shown. The hole on the back of the log should fit over the corresponding pin on the rear log (A). Make sure that the log is positioned so it aligns to the sides of the gas ports on the corner of the burner. 4. Place the left center log (C) as shown. The forked end of the log fits into the corresponding notch on rear log (A). The slot on the other end (bottom) of log fits over the corresponding locating bracket on the sub-fl oor. 5. Place the right center log (D) as shown. One end of the log fits into the corresponding indent on the right log (E). The slot on the other end (bottom) of log fits over the corresponding locating bracket on the subfl oor. LMDV-4035 - Install as Follows Carefully position the ceramic fiber logs and twigs over the burner as shown in Figure 9. Logs should be placed in the order shown and per the following instructions. 1. Position the center log (C) onto the 2 corresponding location pins on the burner. 2. Place the rear log (A) as shown. Position the 2 notches on the bottom of the log over the 2 corresponding locating brackets against the back wall of fi rebox. 3. Place the left log (B) as shown. The notch on the bottom of the log should fit over the corresponding locating bracket. 4. Place the right log (E) as shown. The notch on the bottom of the log should fit over the corresponding locating bracket. Make sure that the log is positioned so it aligns to the sides of the gas ports on the corner of the burner. 5. Place the center front log (D) as shown. The slot in the bottom of the log fits over the corresponding location bracket on the sub-fl oor. WARNING The size and position of the log set was engineered to give the appliance a safe, reliable and attractive flame pattern. Any attempt to use a different log set in the fireplace will void the warranty and will result in incomplete combustion, sooting, and poor fl ame quality. WARNING This appliance is not designedto burn wood. Any attempt todo so could cause irreparabledamage to appliance and provehazardous to your safety. WARNING If logs are not installed accordingto the log installation instructions, flame impingement and improper combustion could occur and result in soot and/or excessive production of carbon monoxide (CO), acolorless, odorless, toxic gas. Glowing Embers Bag of Glowing Embers (rockwool) Separate into Quarter Size (separate) Pieces Figure 7 WARNING DO NOT attempt to install the logsuntil the appliance installationhas been completed, the gas linecon...
Эта инструкция также подходит к моделям:Газовые нагреватели - DIRECT VENT MERIT LMDV-35 SERIES (1.62 mb)
Газовые нагреватели - DIRECT VENT MERIT LMDV-40 SERIES (1.62 mb)