Оценок - 2, средний балл: 4 ( )

Производитель: Majestic Appliances Размер: 2.22 mb Название файла: Язык инструкции:

Attach cover plate to switch. 3. Connect wiring to gas valve. (Fig. 13) UVS33/36 Vent-Free Heaters W584-9 Thermopile Fig. 13 Remote switch wiring. Alternate Switch Location Remote switch can be installed on either side of the access door. Simply mount the switch to the switch bracket provided. Screw the bracket on either side of the frame, lining up the screws with the pre-punched holes. (Fig. 14) FP381 Fig. 14 Installing remote switch bracket. Finishing CAUTION: All joints between the finished wall and the heater surround (top and sides) may be sealed only with noncombustible material. Only noncombustible material can be applied as facing to the heater surround (the black painted face). When finishing the heater, never obstruct or modify the air inlet/outlet top or bottom grilles in any manner. Finish the wall with the material of your choice. Maintain minimum clearances when installing a combustible mantel or other combustible projection. 10 20002211 11 UVS33/36 Vent-Free Heaters 20002211 Operating Instructions LG117.. UVS33 logs.. 12/20/99 djt Fig. 17 UVS33 log placement. Top Left Log (A20) Rear Log (A19) Top Right Log (A21) Front Left Log (A17) Front Right Log (A18) LG117 Burner Lava Rock Lava Rock Top Louvre (Grille) Removal To remove the top louvre (grille) assembly, lift louvre up and then out. (Fig. 15) Window Frame Removal 1. Shut off gas. (Refer to Lighting Instructions) 2. Let the unit cool if it has been operating. 3. Remove top louvre. (Refer to Top Louvre Removal) 4. Open the bottom louvre assembly. 5. Release the two clamps at the bottom of the window frame by pulling down on the clamp handles. Fig. 15 Louvre installation and removal. FP444 1. 2. FP444.. remove louvre.. 12/99 Top Louvre (Grille) Assembly Window Frame Fig. 16 Window Frame installation and removal. DV34-2 Glass removal 12/99 Clamps Fireplace Front DV34-2 FP1000 install glass 12/99 Window Frame Pull Clamp Hook Push Clamp Handle FP1000 Window Frame 6. Lift off the window frame as shown in Figure 15. 7. To reinstall window frame follow the above procedure in reverse. (Fig. 16) Log Installation UVS33 1. Remove window frame. (See "Window Frame" section) 2. Remove logs from packaging. As with all plastic - these are not toys and should be kept away from children and infants. 3. Place rear log on rear bracket (ensure log is seated properly, leveled and centered to the unit), so it will not move from side to side and it is firmly positioned on the bracket. 4. Place front left log on top of burner, left side. Use log's bottom holes to locate it onto the left bracket log locator studs. 5. Place front right log on top of burner, right side. Use log's bottom holes to locate it onto the left bracket log locator studs. 6. Place top left log onto locator notches. Ensure log is secure. 7. Place top right log onto locator notches. Ensure log is secure. UVS33/36 Vent-Free Heaters Log Installation UVS36 1. Remove window frame. (See "Window Frame" section) 2. Remove logs from packaging. As with all plastic - these are not toys and should be kept away from children and infants. 3. Place rear log (BE8) on rear bracket (ensure log is seated properly, leveled and centered to the unit), so the log will not move form side to side and is firmly positioned onto the bracket. 4. Place front left log (BE6) on top of burner, left side. Use log's bottom holes to locate it onto the left bracket log locator studs. 5. Place front right log (BE7) on top of burner right side. Use log's bottom holes to locate it onto the left bracket log locator studs. Front Left Log (BE6) Rear Log (BE8) Top Right Log (BE10) Top Left Log (BE9) Front Right Log (BE7) LG131 Fig. 18 UVS36 log placement. 6. Place ember material on top of burner. (Refer to "Ember Material Placement"). 7. Place top left log (BE9) onto locator notches. Ensure log is secure. 8. Place top right log (BE10) onto locator notches. Ensure log is secure. Ember Material Placement Separate the ember material into small pieces and place onto the burner in front of the front logs. Do NOT pack down, leave in fluffy, loose condition for most realistic ember effects. Do not install more embers on the burner than come with the unit. Application of excess loose material may adversely affect performance of theheater. Replacement loose embers must be purchased through authorized Majestic Fireplaces dealers. WARNING: All previously applied loose material must be removed prior to reapplication. Lava Rock The lava rock provided with this fireplace must be placed on the firebox bottom on either side of the burner assembly. Do not place lava rock directly on burner. (Fig. 18) Under no circumstances should this lava rock be placed on any part of the burner assembly. First Firing .......... Upon completing your gas line connection, a small amount of air will be in the lines. When first lighting ................... unit with pilot light, it will take a few minutes to purge .......... themselves of this air. Once the purging is comple...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: