Войти:
Оценок - 3, средний балл: 4.3 ( )

Инструкция по эксплуатации Enerco, модель MHVFR20LPT

Производитель: Enerco
Размер: 1.8 mb
Название файла:
Язык инструкции:
Перейти к скачиванию



Фрагмент инструкции


If screen or grille guard is removed for servicing it must be replaced prior to operating the heater. WARNING: If you smell gas: • Shut off gas supply • Do not try to light any appliance • Do not touch any electrical switch; do not use any phone in your building • Immediately call you gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors and possible discoloration of walls and ceilings. OBSERVED SYMPTOM POSSIBLE CAUSE REMEDY When ignitor button is pressed in, there is 1. Ignitor electrode positioned wrong. 1. Reposition electrode no spark at pilot 2. Ignitor electrode is broken. 3. Ignitor electrode not connected to ignitor. 4. Ignitor cable pinched or wet. 5. Broken ignitor cable. 6. Bad Piezo ignitor. 7. Low Battery. 2. Replace electrode 3. Reconnect ignitor cable 4. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry. 5. Replace ignitor cable 6. Replace control valve 7. Replace battery ODS/pilot lights but flame goes out when 1. Gas supply turned off or equipment 1. Turn on gas supply turn off or open control knob is released shutoff valve closed. 2. Control knob not fully pressed in while pressing ignition button. 3. Air in gas line when installed. 4. ODS/pilot is clogged. 5. Gas regulator setting is not correct 6. Control knob not in pilot position equipment shutoff valve closed 2. Fully press in control knob while pressing ignition button 3. Continue holding down control knob. Repeat ignition operation until air is removed. 7. Thermocouple connection loose at control valve 8. Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot flame to go out. This problem could be caused by one or both of the following: a. Low gas pressure b. Dirty or partially clogged ODS/pilot 4. Clean ODS/pilot (see Cleaning and Maintenance pages 11 and12). 5. Replace gas regulator 6. Turn Control knob to pilot position When ignitor button is pressed in, there is 1. Control knob not fully pressed in. 1. Press in control knob fully a spark at the ODS/pilot but no ignition 2. Control knob not pressed in long enough 3. Equipment shutoff valve not fully open 4. Thermocouple damaged 5. Control valve damaged 2. After ODS/pilot lights, keep control knob pressed in for 30 seconds 3. Fully open equipment shutoff valve 4. Hand tighten thermocouple nut until snug, and then tighten 1/4 turn more. 5. a. Contact local gas company b. Clean ODS/pilot (see Cleaning and Maintenance, pages 11 and 12). 6. Replace thermocouple 7. Replace Control valve. Unvented LP-Gas Vent Free Room Heaters 14 Installation Instructions and Owner’s Manual Burner does not light after ODS/pilot is li...

Эта инструкция также подходит к моделям:
Газовые нагреватели - MHVFR30LPT (1.8 mb)
Газовые нагреватели - HSVFB20LPT (1.8 mb)
Газовые нагреватели - HSVFB30LPT (1.8 mb)
Газовые нагреватели - HSVFR20LPT (1.8 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории