Войти:
Оценок - 3, средний балл: 4.3 ( )

Инструкция по эксплуатации Enerco, модель HSVFR10LP

Производитель: Enerco
Размер: 1.52 mb
Название файла:
Язык инструкции:
Перейти к скачиванию



Фрагмент инструкции


If you can, provide greater clearances from the floor and joining wall. 2. Mark screw locations on wall (see figure 7). 3. Remove tape and mount bracket from wall. Adjoining Wall17-1/2” Min. 6-1/2” Min. 10,000 BTU 10-1/4” min 20,000-30,000 BTU 16” (Lg) 12-9/64” (Sm) Mark mounting hole locations and drill holes where indicated. Allow for minimum clearances Figure 7 Attaching to Wall Stud: For attaching mounting bracket to wall studs 1. Drill holes at marked locations using 9/64” drill bit. 2. Place mounting bracket onto wall. Line up holes on each end of bracket with hole drilled in wall. 3. Insert mounting screws through bracket and into wall studs. 4. Tighten screws until mounting bracket is firmly fastened to wall studs. Attaching to Wall using Anchor: For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry) Note: Wall anchors, mounting screws, and spacer are in hardware package. The hardware package is provided with heater. 1. Drill holes at marked locations using 5/16” drill bit. For solid walls (concrete or masonry), drill at least 1” deep. 2. Fold wall anchor as shown in figure 8 below. Figure 8. 3. Insert wall anchor (wings first) into hole. Tap anchor flush to wall. 4. For thin walls (1/2” or less) insert red key into wall anchor. 5. Place mounting bracket onto wall. Line up holes on each end of bracket with wall anchors. 6. Insert mounting screws through bracket and into wall anchors. 7. Tighten screws until mounting bracket is firmly fastened to wall. Placing Heater on Mounting Bracket 1. Locate two horizontal slots on back pane of heater (see figure 9). 2. Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket. Horizontal Slots Mounting Bracket mounted to wall Figure 9 Installing Bottom Mounting Screws 1. Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see figure 10). Unvented Liquid Propane Fired Room Heater 7 Installation Instructions and Owner’s Manual Screw Screw hole hole Figure 10 2. Mark screws locations on wall. 3. Remove heater from mounting bracket. 4. If installing bottom mounting screw into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching to Wall using Anchor. If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64” drill bit. 5. Re-place heater onto mounting bracket. 6. Place spacers between bottom mounting holes and wall anchor or drilled hole. 7. Hold spacer in place with one hand. With the other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole. 8. Tighten both screws until heater is firmly secured to wall. Do not over tighten. Note: Do not re-place front panel at this time. Replace front panel after making gas connections and checking for leaks. FLOOR MOUNTING AWAY FROM WALL: Install...

Эта инструкция также подходит к моделям:
Газовые нагреватели - HSVFB10LP (1.52 mb)
Газовые нагреватели - HSVFB10LPT (1.52 mb)
Газовые нагреватели - HSVFR10LPT (1.52 mb)
Газовые нагреватели - MHVFR10LP (1.52 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории