Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Note: If pilot goes out, repeat steps 4 through 8. 9. Slightly push in and turn control knob counterclockwise to the ON position. 10. Wait one minute and switch selector switch to the ON position to light burners. 11. Set flame adjustment knob to any level between HI and LO. CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve. Operating Heater Continued Control Knob Selector Switch LOIHOFFPILOTONAUTOOFFON Flame Adjustment Knob Ignitor Button Figure 11 - Control Knob and Ignitor Button Locations WARNING: Make sure selector switch is in to OFF position when you are away from home for long periods of time. Appliance will come on automatically with selector switch in the ON position. TO TURN OFF GAS TO APPLIANCE Shutting Off Heater 1. Turn control knob clockwise to the OFF position. 2a. Set selector switch in the OFF position. 2b. If Using Optional Hand-Held Remote: Set selector switch in the OFF position to prevent draining battery. Shutting Off Burner Only (pilot stays lit) You may shut off the burners and keep the pilot lit by doing one of the following: 1. Turn control knob clockwise to the PILOT position. 2. Use remote control manual OFF button. 3. Set selector switch in the OFF position. MANUAL LIGHTING PROCEDURE 1. Follow steps 1 through 6 under Lighting Instructions, page 16. 2. Depress control knob and light pilot with match. 3. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow steps 9 through 11, Lighting Instructions, page 17. Optional Hand-held REMOTE control OPERATION 1. After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Set toggle selector switch to AUTO. Slide remote selector switch to REMOTE position (see Figure 13). Note: The burner may light if hand-held remote was on when selector switch was last turned off. You can now turn the burner on and off with the hand- held remote control unit. IMPORTANT: Do not leave the selector switch in the REMOTE or ON position when the pilot is not lit. This will drain the battery. 2. Press ON/OFF button to turn burners on and off. When turning burners off, the pilot will remain lit. IMPORTANT: Be sure to press ON/OFF buttons on hand-held remote control unit for up to 3 seconds to assure proper operation. Remote Control Specifications Batteries: (See instructions with remote for removing and installing batteries) Transmitter requires 12V (A-23) and 3V button cell for LCD (both included) Remote receiver requires 4 AA (1.5V) alkaline batteries (included) Operating Frequency: 303.875 MHz Operating Heater Continued Natural Propane/LP Figure 12 - Pilot (Remote Shown) Remote Selector Switch Control Knob LOIHOFFPILOTONOFF REMOTE ONAUTOOFFON Flame Adjustment Knob Selector Switch in AUTO Position Ignitor Button Figure 13 - Control Knob and Ignitor Button Locations for Remote Control Inspecting Burners Check pilot flame pattern and burner flame patterns often. PILOT FLAME PATTERN Figure 14 shows a correct pilot flame pattern. Figure 15 shows an incorrect pilot flame pattern. The incorrect pilot flame is not touching the thermocouple. When the thermocouple cools, the heater will shut down. If pilot flame pattern is incorrect, as shown in Figure 15 • turn heater off (see To Turn Off Gas to Appliance, page 12) • see Troubleshooting, page 15 Note: The pilot flame on natural gas units will have a slight curve, but flame should be blue and have no yellow or orange color. BURNER FLAME PATTERN Figure 16 shows correct burner flame pattern. NOTICE: Do not mistake orange flames with yellow tipping. Dirt or other fine particles are burned by heater, causing brief patches of orange flame. If burner flame pattern is incorrect, as shown in Figure 17 • turn appliance off (see To Turn Off Gas to Appliance, page 12 • see Troubleshooting, page 15 Yellow Flames with Orange Streaks Pilot Burner Thermocouple Thermocouple Figure 16 - Correct Burner Flame Pattern Figure 14 - Correct Pilot Flame Pattern (Your Pilot May Differ from Pilots Shown) Dark Orange Flames Pilot Burner Thermocouple Thermocouple Figure 15 - Incorrect Pilot Flame Pattern (Your Pilot May Differ from Pilots Shown) Figure 17 - Incorrect Burner Flame Pattern Cleaning and Maintenance WARNING: Turn off heater and let cool before cleaning. CAUTION: You must keep control areas, burner and circulating air passageways of fireplace clean. Inspect these areas of fireplace before each use. Have fireplace and chimney inspected yearly by a qualified service person. Fireplace may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc. Only limited cleaning will be required under normal use of this appliance. Dust front grate and top of receiver/valve. Do not use cleaning fluids to clean logs or any other part of the appliance. If after a period of use the flames start to exhibit unusual shapes and behavio...