Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Use fresh fuel next season. See STORAGE Instructions for additional information. CaUTiOn Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. NOTE: Check the fuel level periodically to avoid running out of gasoline while operating the Yard Vacuum. If the unit runs out of gas as it is chipping, it may be necessary to unclog the discharge area before it can be restarted. Refer to SERVICE AND MAINTENANCE section. 1 14 OPERATION TO STAR T ENGINE Attach spark plug wire and rubber boot to spark plug. The bag/chute switch button must be fully depressed by the tip of front tab on bag handle or blower chute for engine to start. Make sure bag/chute switch wire is connected to engine and grounded to mounting bracket. Gas tank should be filled 3/4 to full before starting. Move throttle control to START/RUN (Rabbit) position. See Figure 11. Move the choke control toward the throttle control to choke the engine’s carburetor. (A warm engine may not require choking.) See Figure 11. Standing behind the unit, grasp starter handle and pull rope out until you feel a drag. Pull the rope with a rapid, continuous, full arm stroke. Keep a firm grip on the starter handle. Let the rope rewind slowly. Repeat, if necessary, until engine starts. When engine starts, move choke control gradually away from the throttle control. If engine falters, move choke control back toward the throttle control and repeat steps 7 through 9. ALWAYS keep the throttle control in the START/RUN position when operating the Yard Vacuum. TO STOP ENGINE Move throttle control lever to slow (turtle) position. Whenever possible, gradually reduce engine speed before stopping engine. Move throttle control lever to STOP or OFF position. Disconnect spark plug wire and ground it to the retaining post to prevent accidental starting while the equipment is unattended. TO EMPTY BAG Unhook bag straps from the lower handle. Unsnap bag clip from the top of lower handle. See Figure 12. Grasp bag handle with one hand and pull lock rod on mounting bracket with other hand toward engine to release. Lift bag off back of unit. Twist the two buttons on the back of the bag to unlock and empty contents. See Figure 13. Hold bag handle and bag clip while emptying the contents. Compress bag opening and fold inner flap over opening. Fold outer flap over inner flap and insert buttons on the bag through metal outlets. See Figure 13. Twist the buttons to lock bag. Place bag back onto unit as instructed in the ASSEMBLY section. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 1. 2. 3. 1. 2. 3. 4. 5. 6. 7. 8. Figure 12 Figure 11 Throttle Control Choke Control WARNING When moving throttle control lever, be careful of heated surfaces and sharp edges on muffler guard. Outer Flap Inner Flap Buttons 1 2 3 4 Figure 13 OPERATION TO reMOVe BLOWer CHUTe 1. Grasp blower chute with one hand and pull lock rod on mounting bracket with other hand toward engine to release. Refer to Figure 8 in the ASSEMBLY section. 2. Remove blower chute from over the rim of the discharge opening. USing THe nOZZLe VaCUUM 1. Place nozzle/hose vac lever in the top position on the nozzle to vacuum through nozzle. See Figure 14. 2. The spring loaded pin must be in the first hole (closest to the end of the tube) of the hose adapter to operate the nozzle vac. 3. Place both hands on top of the upper handle and fully lift the drive control against the upper handle to propel the unit over yard. 4. Use the speed control to choose either the high or low speed. The speed control may be moved either while the unit is propelling or before engaging the wheels. IMPORTANT: Move the speed control only when the engine is running. Changing the speed control setting with the engine off can Figure 14 damage the yard vacuum. Yard waste such as leaves and pine needles can be vacuumed up through the nozzle for shredding. After material has been shredded by the flail blades on the impeller assembly, it will be discharged into catcher bag or through blower chute. Do not attempt to shred or chip any material other than vegetation found in a normal yard (i.e. branches, leaves, twigs, etc.) Avoid fibrous plants such as tomato vines until they are thoroughly dried out. Materials such as stalks or heavy branches up to 1-1/2” in diameter may be fed into the chipper chute. IMPORTANT: The flail screen is located inside the housing in the Warning Do not attempt to shred, chip, or vacuum any material larger than specified on the machine or in this manual. Personal injury or damage to the machine could result. discharge area. If the flail screen becomes clogged, remove and clean Figure 15 as instructed in the SERVICE & MAINTENANCE section. For best performance, it is also important to keep the chipper blade sharp. Warning Do not at any time make any adjustments without first stopping engine and disconnecting spark plug wire. USing THe HOSe aSSeMBLY 1. Place nozzle/hose vac handle in the bottom position on the nozzle to redirect vacuum...