Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Use the end of mounting bracket as leverage when sliding the locking rod. See Figure 7. Slip blower chute over rim of discharge opening and release locking rod to secure chute in place, as in Figure 7. Raise the nozzle height to the highest setting when using the blower chute. Refer to nozzle height adjustment in the next section. NOTE: The bag/chute switch button attached to the mounting bracket must be fully depressed by the tip of front tab on the blower chute or engine will not start. NOZZLE HEIG HT ADJUSTMEN T The nozzle can be adjusted to any five positions, ranging from 5/8” to 4 1/8” ground clearance. The nozzle height has to be adjusted according to yard conditions. Depress nozzle height adjustment lever towards wheel. See Figure 8. Move the height adjustment lever forward or backward to adjust the nozzle upwards or downwards. Make sure both levers are in the same position. Release lever towards deck. NOTE: In general, raise the nozzle height to vacuum a thick layer of leaves or to operate with the blower chute. Lower the nozzle height for smoother surfaces. 1. 2. 3. 1. 2. 3. Figure 8 1 2 3 B 1 2 12 OPERATION Figure 9 Now that you have set up your yard vacuum for operation, get acquainted with its controls and features. These are described below and illustrated on this page. This knowledge will allow you to use your new equipment to its fullest potential. Chipp er Chut e Allows twigs and small branches up to 1-1/2” in diameter to be fed into the impeller for chipping. See Figure 9. nozzl e Yard waste such as leaves or pine needles can be vacuumed up through the nozzle for shredding. bag Collects shredded material fed through the chipper chute or vacuumed through the nozzle. Blow er Chut e When attached to unit, the blower chute is used to discharge yard waste such as leaves, pine needle, or small twigs across yard. Bag Handl e Used to grasp bag in order to assist in attaching, removing, and emptying bag. See Figure 9. Nozzl e Height Adjustm ent Lever Used to adjust the nozzle ground clearance ranging approximately from 5/8” to 4 1/8”. Meets ANSI Safety Standards Craftsman Yard Vacuums conform to the safety standard of the American National Standards Institute (ANSI). WARNING The operation of any yard vacuum can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear the safety glasses provided with this unit or eye shields while operating or performing any adjustments or repairs on it. Blower Chute Throttle Control Choke Control Chipper Chute Bag Handle Starter Handle Oil Fill Bag Nozzle Gasoline Fill Nozzle Height Adjustment Lever OPERATION THrOTTLe COnTrOL This lever controls the engine speed and stop function. Through three separate positions on the lever from left to right, the operation is as follows: CHOke COnTrOL The choke control is used to choke the carburetor and assist in starting the engine. STarTer HanDLe Used to start the engine. gaS anD OiL FiLL-UP Oil (one bottle shipped with unit) First Time Use Remove oil fill dipstick. With the Yard Vacuum on level ground, use a funnel to empty entire contents of oil bottle provided into the engine. Replace oil fill dipstick and tighten. Subsequent Uses Only use high quality detergent oil rated with API service classification SF, SG, or SH. Select the oil’s SAE viscosity grade according to the expected operating temperature. Follow the chart below. 1. 2. 3. gasoline Remove fuel cap from the fuel tank. Make sure the container from which you will pour the gasoline is clean and free from rust or foreign particles. Never use gasoline that may be stale from long periods of storage in its container. Gasoline that has been sitting for any period longer than four weeks should be considered stale. Fill fuel tank with clean, fresh, unleaded regular gasoline only. Do not use gasoline containing METHANOL. Replace fuel cap. NOTE: Check the fuel level periodically to avoid running out of gasoline while operating the Yard Vacuum. If the unit runs out of gas as it is chipping, it may be necessary to unclog the discharge area before it can be restarted. Refer to SERVICE AND ADJUSTMENT section. 1. 2. 3. STOPStart/ Run Slow/ Idle Engine Off Oil Viscosity Chart 5W30 Colder Warmer SAE30 Warning Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes, and other sources of ignition. CaUTiOn Use Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. CaUTiOn To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE Instructions for addit...