Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Adjusts for various height tractor hitches. Drawbar Offset Tube Allows drawbar to be offset from tractor. HOW TO USE YOUR SWEEPER SWEEPING SPEED Do not exceed 6 m.p.h.• Try a starting speed of approximately 3 m.p.h. (third gear on most tractors). Depending on conditions, it may be necessary to adjust the sweeping speed in order to achieve best results. CAUTION: Maximum towing speed is 6 m.p.h. Driving too fast may cause damage to wheels and bearings. BRUSH HEIGHT ADJUSTMENT To adjust sweeper brushes to best operating height, • loosen adjustment knob and push down on height adjustment lever to raise the brush, or push up on the lever to lower the brush. See figure above. Best adjustment is when the brush setting is 1/2" down into the grass. Always mow the grass to an even height before sweeping. DUMPING OF SWEEPER Your sweeper can be dumped without getting off of • the rider or tractor. Unclip dump lever from pivot rod and pull forward to empty the hopper. Always empty hopper after each use. CAUTION: Keep sweeper away from fire. Excessive heat can damage the brushes and hopper bag and could cause the bag and its contents to burn. DRAWBAR OFFSET The drawbar can be attached to the center, left hand • or right hand set of holes in the drawbar offset tube. maintenance CUSTOMER RESPONSIBILITIES Read and follow the maintenance schedule and the procedures listed in the maintenance section. Before storage Every two years Every season Twice a year Before each use After each use MAINTENANCE SCHEDULE Fill in dates as you complete regular service. Service Dates Check for loose fasteners X Check for worn or damaged parts X X Lubricate brush shaft bearings X Lubricate wheel bearings X Clean Sweeper X X Clean/Lubricate chain and sprockets X scheduled maintenance Clean the sweeper after each use.• Inspect for worn or damaged parts, such as brushes • and wheels. Lubricate the brush shaft bearing twice a with a few • drops of light weight oil. Every two years, remove wheels and clean sprockets, • chains, and gears found inside the wheel housing. After cleaning, lubricate with an even coat of light grease. To remove the wheel, pop off the hub cap using a screwdriver and remove the lock nut and flat washer. Cleaning Clean sweeper housing with a soft brush or cloth.• Clean debris from hopper bag with a brush or broom.• Remove any material which has wrapped around • brushes or ends of brush shaft. troubleshooting Wheels skid when sweeping Brushes set too low.• Adjust height till brushes are 1/2" down into grass.• Brushes are jammed.• Stop sweeper. Remove obstruction.• Wheels are jammed.• Remove one wheel at a time to check for obstruction • or damage Refer to Service and Adjustments section. storage CAUTION: Before storing the sweeper, always empty hopper bag to avoid spontaneous combustion. Clean the sweeper and hopper bag thoroughly to • help prevent rust and mildew. To collapse the hopper bag for storage, remove the • two hopper support rods from the rear of the hopper. Remove the hitch pin (20) from the center hole, fold • the drawbar to the right or left and then replace hitch pin (20). Refer to figure 5 on page 6. Remove plastic wing nuts (31) from bag arm channel. • Fold bag arm channels into sweeper housing and replace plastic wing nuts (31). Refer to figure 3 on page 5. Store in a dry area.• service and adjustments brush replacement NOTE: Replace brushes one brush at a time. Remove the hopper bag from the sweeper.1. Loosen hex bolts and lock nuts on two single brush 2. retainers which clamp one brush to the double brush retainers. DO NOT loosen or remove bolts which fasten double brush retainers to brush shaft. Slide the brush out of the retainers, noting on which 3. side of the brush the bristles overlap. Install new brush, making sure the bristles overlap on 4. the same side of the brush as before. Sprocket, CHAIN and Pawl Service IMPORTANT: Do Not remove both wheels at the same time to avoid mixing of parts. (The R.H. and L.H. ratchet sprockets are not interchangeable.) Make notes on the position of all parts before removing them. Remove hub cap, nylock nut and washer on outside • of wheel and then remove wheel. Remove the dust cover by removing the two #12 • screws which fasten it to the wheel housing. (It is not necessary to remove the dust cover if you are only cleaning and lubricating the chain and sprockets.) Remove the retaining rings and washers which hold • the sprockets onto the shafts. Remove the chain and both sprockets, holding them • in position and sliding them off both of the shafts. (Look for the drive pin, which may fall out of the brush shaft when the ratchet sprocket is removed.) See figure 22. To reassemble, insert the drive pin through the hole • at the end of the brush shaft. Make sure the pin slides back and forth easily in the shaft. Lightly grease both shafts and the chain, and fill the • ratchet sprocket with grease. Assemble the chain with both sprockets back onto the shafts. Lightly grease ...