Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. MODEL 22610709 - 12 TORO Z-MASTER 2001 PECO 3 PECOPECOPECOPECOPECOASSEMBLY PECOPECOPECOPECOPECOASSEMBLY 4 STEP 1: TO FASTEN CHANNEL CLAMP (A) TO MOUNT PLATE (B) USE (4) 3/8"-16 x 1" HEX BOLTS (#K1191) AND (4) 3/8"- 16 FLANGE NUTS (#K1215). USE FIGURE 1-1 TO PLACE BOLTS. FIGURE 1-1 HOLES TO MOUNT CHANNEL CLAMP A B HOLES FOR MOUNTING TO MOWER A STEP 2: TO MOUNT MOUNT PLATE (A) TO THE MOWER FRAME USE (2) 3/8"-16 x 3" U-BOLTS (#K1118) AND (4) 3/8"-16 FLANGE NUTS (#K1215). USE FIGURE 1-1 TO PLACE BOLTS. MODEL 22610709 - 12 TORO Z-MASTER 2001 PECO ASSEMBLY A B STEP 3: Slide Engine Mount Arm (B) into the receiver on the Mount Plate (A) and fasten by dropping in ball pin (#J0248). Place Engine/ Blower Assembly onto Engine Mount Arm (B) and fasten with (4) 5/16"-18 x 1 1/2 hex bolts (#K1157) and (4) 5/16"-18 flange nuts. Tighten nuts and bolts. STEP 4: The ears of the Cone (A) should fit underneath the two threaded bosses on the Blower Face (B). Secure with (2) 5/16"-18 x 2" cone bolts. TIGHTEN CONE BOLTS BEFORE EACH USE! PECO PECOPECOPECOPECOPECO A B A BImpeller Blade Replacement To remove: Remove hex bolts from hub then screw the bolts into threaded holes to remove old blade. (This will push the impeller off the hub.) If the impeller is stuck on hit the base of the impeller between each vein with a hammer then try the bolts again. To replace: Place tapered bushing (A) into hub (B) and align non-threaded holes with the holes in the hub. Secure with two 1/4" x 1" hex bolts. Torque to 15 ft. lbs. MODEL 22610709 - 12 TORO Z-MASTER 2001 PECO 5 PECOPECOPECOPECOPECOPARTS LIST REF. NO. PART NO. DESCRIPTION QTY. 1 ******* BOOT PLATE (SPECIFY DECK SIZE) 1 2 ******* BOOT (SPECIFY DECK SIZE) 1 3 J6006 7"-8" HOSE CLAMPS 2 4 ******* 7" x 48" LOWER HOSE 1 5 E6004 7" BLOWER CONE 1 6 ******* ENGINE/BLOWER/BLADE ASSEMBLY 1 E4052A BLOWER HOUSING D4002 5HP BRIGGS & STRATTON ENGINE A0645 4 BLADE IMPELLAR W/ S4311 BUSHING W/ 3/4" SHAFT D1016 6HP KOHLER ENGINE A0914 4 BLADE IMPELLAR W/ S4302 BUSHING W/ 1" SHAFT 7 J6011 5"-6" HOSE CLAMPS 2 8 ******* 6" x 36" LOWER HOSE 1 9 V1054 UPPER INLET 1 10 A0023 HARDTOP ASSEMBLY 1 11 A0913 BASE FRAME ASSY 1 12 A0907 (OPTIONAL) WEIGHT ASSEMBLY 1 13 B2250 CHANNEL CLAMP 1 14 A0917 MOUNT PLATE ASSEMBLY 1 16 A0780 ENGINE MOUNT ASSEMBLY 1 17 B1941 INSIDE INLET PLATE 1 18 B1926 OUTSIDE RETAINING PLATE 1 19 J0316 GAS STRUT 2 20 A0021 RIGHT HAND HINGE PLATE ASSEMBLY 1 21 A0022 LEFT HAND HINGE PLATE ASSEMBLY 1 22 A0236 LATCH ASSEMBLY 2 23 A08221 HARDWARE BAG 1 24 VV2002 PLASTIC CONTAINERS 7 CU. FT. 1PECOPECOPECOPECOPECOPARTS LIST REF. NO. PART NO. DESCRIPTION QTY. 1 ******* BOOT PLATE (SPECIFY DECK SIZE) 1 2 ******* BOOT (SPECIFY DECK SIZE) 1 3 J6006 7"-8" HOSE CLAMPS 2 4 ******* 7" x 48" LOWER HOSE 1 5 E6004 7" BLOWER CONE 1 6 ******* ENGINE/BLOWER/BLADE ASSEMBLY 1 E4052A BLOWER HOUSING D4002 5HP BRIGGS & STRATTON ENGINE A0645 4 BLADE IMPELLAR W/ S4311 BUSHING W/ 3/4" SHAFT D1016 6HP KOHLER ENGINE A0914 4 BLADE IMPELLAR W/ S4302 BUSHING W/ 1" SHAFT 7 J6011 5"-6" HOSE CLAMPS 2 8 ******* 6" x 36" LOWER HOSE 1 9 V1054 UPPER INLET 1 10 A0023 HARDTOP ASSEMBLY 1 11 A0913 BASE FRAME ASSY 1 12 A0907 (OPTIONAL) WEIGHT ASSEMBLY 1 13 B2250 CHANNEL CLAMP 1 14 A0917 MOUNT PLATE ASSEMBLY 1 16 A0780 ENGINE MOUNT ASSEMBLY 1 17 B1941 INSIDE INLET PLATE 1 18 B1926 OUTSIDE RETAINING PLATE 1 19 J0316 GAS STRUT 2 20 A0021 RIGHT HAND HINGE PLATE ASSEMBLY 1 21 A0022 LEFT HAND HINGE PLATE ASSEMBLY 1 22 A0236 LATCH ASSEMBLY 2 23 A08221 HARDWARE BAG 1 24 VV2002 PLASTIC CONTAINERS 7 CU. FT. 1 MODEL 22610709 - 12 TORO Z-MASTER 2001 PECO PECOPECOPECOPECOPECOEXPLODED VIEWPECOPECOPECOPECOPECOEXPLODED VIEW 1 23 4 5 7 6 8 10 9 11 12 13 14 16 17 18 19 20 3 7 2122 22 MODEL 22610709 - 12 TORO Z-MASTER 2001 PECO PECOPECOPECOPECOPECOASSEMBLYPECOPECOPECOPECOPECOASSEMBLY STEP 5: Attach Base Frame (A) to Mount Plate (C) and secure by dropping in ball pin (#J0248). With hood open on the Base Frame (A) insert the 7cu. ft. Canister (B) and close STEP 6: Place Clamps (A) over each end of 6" Hose (B). Attach one end of hose onto Blower Housing (C). Attach free end of hose over Inlet (D). TIGHTEN CLAMPS! C B A REAR VIEW OF MOWER A D B C MODEL 22610709 - 12 TORO Z-MASTER 2001 PECO PECOPECOPECOPECOPECOASSEMBLYPECOPECOPECOPECOPECOASSEMBLY STEP 7: To mount the boot plate (A) to the boot (B) use (2) 3/8"-16 x 1" carriage bolts (K1182) and (2) 3/8"-16 flange nuts (K1178). Besure when bolting together that the head of the bolt is inside the boot. Once boot & boot plate are fastened hang boot to mower as shown. A A STEP 8: For 62" & 72" decks bolt cover plate (A) (B1811) to deck as shown, using 5/16"-18 X 1" hex bolt A (K1154) and 5/16"-18 flange nut (K1178). STEP 9: Place Clamp over each end of Lower Hose. Attach one end of hose over the Blower Cone. Tighten Clamp. Slide free end of hose over Boot and tig...
Эта инструкция также подходит к моделям:Газоноуборщики - 22610709 (334.28 kb)