Оценок - , средний балл:
(
)
)
Производитель: Agri-Fab
Размер: 7.1 mb
Название файла: 45-0456.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Modele no Modelo no 45-0456 44" Lawnsweeper BALAYEUSE A GAZON DE 44 PO. (112 CM) BARREDORA DE CESPED DE 44 PULGADAS (112 CM) FORM NO. 42016 (12/11/08) • Safety • Assembly • Operating • Maintenance • Repair Parts • Seguridad • Montaje • Operacion • Mantenimiento • Piezas de repuesto • Securite • Assemblage • Utilisation • Entretien • Pieces 2 SAFETY RULES Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using power equipment. LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAU TIONS. IT MEANS — ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED. CAU TION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CONDITIONS ON SLOPES. • Read the vehicle and sweeper owners manuals and know how to operate your vehicle and sweeper before using this sweeper attachment. Always instruct other users before they operate the sweeper. • Do not permit children to operate sweeper. • Do not permit anyone to ride on sweeper. • Operate the sweeper at reduced speed on rough terrain, near ditches and on hillsides to prevent loss of control. • Vehicle braking and stability may be affected with the attachment of this sweeper. Do not fill sweeper to maximum capacity without checking the capability of the towing vehicle to safely pull and stop with the sweeper attached. Stay off of steep slopes. • Do not hold onto dump handle while tractor is moving. • Never attach dump handle to tractor or any part of your body. Always keep it secured to the hopper bag while tractor is moving. If any part of dump handle should become damaged, stop use of sweeper and replace the damaged part. • Stop and inspect vehicle and sweeper for damage after striking an object. Repair any damage before continuing operation. • Keep sweeper away from fire. Excessive heat can damage the brushes and hopper bag and could cause the bag and its contents to burn. • Before storing the sweeper, always empty the hopper bag to avoid spontaneous combustion. • Follow maintenance and lubrication instructions as outlined in the maintenance section of this manual. 1 (x1) 2 (x1) 4 (x2) 5 (x1) 6 (x2) 7 (x2) 8 (x2) 9 (x1) 10 (x2) 11 (x2) 12 (x1) 13 (x1) 14 (x1) 3 (x1) 42020 40890 43938 23014 40892 26408 26414 24192 26413 40893 40897 41041 40894 40989 3 ASSEMBLY INSTRU CTIONS assembly of 44" Lawnsweeper 1. Slide the bag arm channels (4) into the sweeper housing as shown in figure 1. Secure them to the sweeper housing with a 5/16-18 x 2-1/2" hex bolt (15) and 5/16" nylock nut (21). Tighten bolt until secure. Do not over tighten. 44292 43648 43182 43343 47810 44917 23368 47189 712-3046 7071 26484 712-0421 41036 43978 43501 43055 47623 48365 41013 23878 23353 15 (x7) 16 (x1) 17 (x4) 24 (x6) 18 (x1) 27 (x2) 26 (x5) 19 (x3) 28 (x2) 20 (x1) 32 (x2) 31 (x2) 33 (x1) 34 (x1) 35 (x1) 29 (x1) 30 (x2) 25 (x2) 21 (x9) 22 (x2) 23 (x2) shown full size figure 1 15 4 21 4 2. To lock the bag arm channels into position, secure each of them to the side of the sweeper housing with a 5/16-18 x 3/4" hex bolt (17), a 5/16" jam nut (25) (between the bag arm channel and the sweeper housing) and a plastic wing nut (31). See figure 2. 3. Slide a pivot rod retainer (30) into each end of the bag arm channels. See figure 3. 4. Insert a compression spring (32) into the bottom of each of the pivot rod retainers to secure them to the bag arm channels. See figure 3. figure 2 figure 3 figure 4 figure 5 5. Attach the drawbar (14) to the sweeper by fastening a drawbar bracket (8) above and below the drawbar with three 5/16" x 2-1/2" hex bolts (15) and 5/16" nylock nuts (21). See figure 4. 6. Lock the drawbar into position by inserting a 3/8" x 3" hitch pin (20) into the center hole and securing it with a 3/32" cotter pin (19). See figure 5 17 31 25 20 19 8 15 14 21 8 30 32 5 figure 6 figure 8 figure 9 figure 7 7. Attach the hitch bracket (12) and straight hitch bracket (13) to the drawbar using two 5/16" x 2-1/2" hex bolts (15) and 5/16" nylock nuts (21). See figure 6. 8. Assemble a 3/8" x 3" hitch pin (35) and two 3/4" spacers (22) to the hitch brackets. Secure them in place with a 3/32" hair cotter pin (18). See figure 6. 9. Slide ends of two lower hopper tubes (10) into the flaps at the front of the hopper bag (3) as shown in figure 7. 10. Slide a rear hopper tube (11) onto ends of lower hopper tubes (10) making sure the holes in the rear hopper tube are facing up as shown in figure 8. 11. Secure the rear hopper tube (11) to the lower hopper tubes (10) with two 1/4" x 1" curved head bolts (26) and 1/4" nylock nuts (24). See figure 8. NOTE: Hopper bag (3) not shown for clarity. 12. Slide the upper hopper tubes (6) through flaps in the sides of the hopper bag (3) as shown in figure 9. 13. Slide the upper hopper tubes (6) up inside the hopper bag (3) as shown in figure 9. 21 3 6 3 10 13 12 15 35 22 18 24 24 11 10 10 26 26 6 figure 1...