Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Pins (58) and Cotter Pin (62). Wrap Cotter Pin around Clevis Pin as shown in Figure 9. Secure the Rope (78) to the top cen13. ter of the Hopper Bag Frame. Secure the Wind Screen (31) to the 14. Upper Hopper Tube (9). Stretch out all four corner loops and snap into place. Wrap the rear loops around the Upper Hopper Tube for a secure fit. Bag Mount Arm (48) BagRetainer (66) Figure 10 15. Secure the Hopper Bag Frame (12) to the Sweeper by hooking the Clevis Pins into the notches in the Mount Arms-see Figure 10. To remove the Hopper Bag Frame 16. from the Sweeper, flip the Bag Retainers up and remove the Bag-see Figure 10. Adjusting Lawn Sweeper to the Towing Vehicle The Sweeper must be secured to the 1. towing vehicle so that the bottom of the Bag Frame (12) is approximately level when on a flat surface. The Bag Frame must be off the ground 3” to 4”. Do not allow the Bag Frame to drag on the ground. Remove the Bag for storage.2. Adjust Spacers (77) and Hitch Brack3. et (47) according to the diagram on page 9. The black line represents the tractor hitch. Riding Mowers with 8” to 10-1/2” Ground Clearance to Hitch 1. Tractors with 10-1/2” to 13” Ground Clearance to Hitch Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tractor Hitch Brush Height Adjustment To adjust Sweeper brushes to the 1. best height, loosen the Height Adjustment Knob (5) and push down on the Height Adjustment Handle (69) to raise. For best performance, adjust the brushes so that they set 1/2” down into the grass. Dumping the Sweeper The Sweeper can be dumped easily 1. without getting off of the rider or tractor. Pull the rope forward to dump. Always dump the Sweeper after each 2. use. Damp or wet grass and leaves will cause damage to hopper if stored for long periods of time. Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication BEFORE EACH USE,1. inspect the general condition of the Lawn and Leaf Sweeper. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged and any other condition that may affect its safe operation. Add a few drops of light machine oil 2. to the brush shaft bearins twice a year. Remove wheels to clean gears ev3. ery two years. After cleaning, apply an even coat of light grease. Do not overtighten wheel bolt and nut upon reassembly. Wheel must be free to move in slot with height adjustment. Removing Wheel Figure 11 1. Pop off Hub Cap (90) with a screw driver (not included). Remove Jam Nut (18), Hex Lock Nut and Washer (19)-see figure 11. When servicing Wheel gears, do not 2. remove both wheels at once. Remove one wheel at at a time to prevent use of left-hand parts on right- hand side. Make note of all washers and rings.3. The Drive Pin is located inside of the 4. ratchet gear. When reassembling the ratchet gear and pin, fill the inside of the gear with grease. Reassemble the wheel and rotate it in both directions. The wheel should drive the brushes only when turned in the for ward direction. If the brushes move in both directions, then the Drive Pin is jamming inside the Ratchet Gear. Make certain that the gear is clean and greased adequately. Replacing Brushes Oil Bearing hereFigure 12 1. Replace Brushes one at a time to avoid misplacing right and left-hand side gearing. Remove the Hopper Bag (12).2. Tip the Sweeper back on its housing. 3. Do not remove Hex Bolts which fasten the Double Brush Retainers (40) to the Brush Shaft (39). Loosen the Hex Bolts (73) and Hex 4. Lock Nuts (60). Slide the Brush out of the retainers, making note of the position of the bristles-see Figure 12. Install new Brush, making certain 5. overlapping bristles are positioned the same as before. PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts a...