Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Always disconnect the spark plug wires and place them where they cannot contact the spark plug, to prevent accidental starting the engine when setting up, transporting, adjusting or repairing. • Always wear protective gear such as safety goggles, protective hearing device. • Never wear loose clothing or jewelry that can be caught by moving parts of the vacuum and pull you into it. Keep hair away from moving parts. There are rotating blades inside these opening. 3 • Familiarize yourself with all of the controls in a safe environment before starting to work with this machine. • Keep hands and feet away from moving parts. • Only operate vacuum on slopes of 35% grade or less. • Never operate or allow someone to operate this equipment while under the influence of alcohol or drugs. • Never make adjustments or repairs with the engine running. • Do not remove top cover or attempt to empty contents or make any adjustments of cart while engine is running. • Do not use lawn vacuum if any guards, hoses, adapters, boot or any other damage or repairs are needed. • Vehicle braking and stability are affected by the addition of this equipment. Do not fill the lawn vacuum to its full capacity without checking the towing capacities of the tow vehicle. SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Order by part number from Swisher Mower and Machine Co. Inc. OD70142-DANGER STOP ENGINE DECAL OD55-TRIANGLEDANGERDECAL OD38-CAUTIONS DECAL 4 ASSEMBLY INSTRUCTIONS 1. Remove outside crate and set parts aside. 2. Remove small components and identify each piece. 3. Raise front hitch, using caution to prevent latch from being bent. (Figure 1) 4. Latch hitch to wagon. 5. Align holes in frame and install 3/8-16X1” Hex Head bolt and lock nuts. 6. Tighten all four of the hitch bolts securely. (Figure 2) 7. Insert hitch tube into the front of the hitch and lock in place with the snap pin (H11). 8. Lower trailer down on the wheels and roll off of the pallet. 9. Align fan/engine/pump assembly on lower slots of motor base with the rivets, pushing down and rearward to align the front holes. (Figure 3) 10. Install 3/8-16X1” bolts in front holes and tighten. 11. Unfold fabric bag frame and place into pockets at the corner of the bed. (Figure 5) 12. Install tailgate by sliding downward into the rear channels. 13. Open fabric bag and spread over the top frame stretching downward and slipping the plastic edge under the edge of the trailer bed rail. 14. Attach the Velcro tabs around the rear frame section and zip the rear flap closed. 15. Insert the bag adaptor into the bag sleeve at the front upper left hand corner 16. Install upper tube onto blower and lock into place. 17. Install hose onto the front of the blower housing and secure clamp. 18. Cut boot to fit deck and install to deck. (Figure 4) 19. Assemble end of hose and a hose clamp over the round opening of boot and tighten clamp. PREPARING THE DECK BOOT • View the boot templates that are provided. Select the template that corresponds with the discharge opening of mowing deck. If a template does not exist for your mower, then one will need to be created. • To create a custom template, mark around your discharge opening on a piece of cardboard. • Tape the template to the face of the boot, locating the template approximately .” from the front edge and .” down from the top. Keep as close to the top as possible. Mark outline of template onto the face of the boot using a white crayon, nail or scribe. • Drill a starting hole inside the outline, and then use a key-hole saw or equivalent to cut out the opening. Be sure not to cut the hole too big the first time. • Position the boot over the deck opening and check for fit of cutout. If necessary, trim cutout. Keep the fit as close as possible for best vacuum suction. • A selection of boot brackets is provided. Some bending may be required. Drilling of holes into your existing deck may be necessary, as well as drilling into the top of the boot. ATTENTION! WE HAVE MADE EVERY ATTEMPT TO PROVIDE HARDWARE TO MOUNT THE DECK BOOT TO VARIOUS LAWN MOWING MANUFACTURERS. DUE TO CONSTANT CHANGES IN DESIGNS OF MOWING DECKS SOME ADAPTATION MAY BE NECESSARY. 5 Be careful while lifting, not to bend Move components off of pallet and identify. Bag adapter fits into Figure2latch. Inserttongueandpin. Install4boltsandnuts. Figure 1 Figure 3 Figure 4 Assembleframeintocornerholes. Blowertubeslidesoverdebrisexhaust. bagandoverblowertube. Figure5 6 OPERATING YOUR LAWN VACUUM The operation of any mower can produce foreign objects to be thrown into the eyes, resulting in severe eye damage. Always wear certified safety glasses or wide-vision safety goggles over spectacles before starting any cutting machine and while operating such a machine. The operation of any engine produces sound waves that are damaging to the human ear. Ear protection is recommended. CAUTION! Tragic accidents can occur if the operator is not alert to the presence of children. Children ...