Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
(See figure 1.) 8. Slide the bag over the air duct. 9. Fasten the nozzle to the front of the vacuum with four flat washers and thumb nuts provided. 10. Use the following steps on the self propelled unit only. 11. Fasten the throttle control to the right hand side of the upper handle with one hex screw and hex center locknut provided. 12. Secure throttle control cable to the lower handle with the cable clip provided. NOTE Cable clip must be assembled to lower handle with the open end towards the engine. This will prevent wear to the bag. 13. Place ferrule through control lever. 14. Place flat washer over ferrule and thread control rod into ferrule about eight or nine turns. 15. Hook formed end of control rod in the shifting finger. 16. Place curved face of spacer towards the outside of upper handle left hand side. 4 17. Fasten control lever in position with hex screw and two hex n uts provided. 18. Engage and disengage control lever, check for free pivoting action. It may be necessary to readjust the control rod. OPERATION 1. Service engine with gas and oil. See engine manual packed with vacuum for complete instructions for care and maintenance of engine. READ DIRECTIONS CAREFULLY. START ENGINE After the engine has been properly fueled and oiled (refer to engine operating and maintenance instructions), start engine in the following manner. PUSH MODEL 1. Move throttle control lever on engine to START position. 2. Crank engine. Pull recoil with a quick firm pull. Do not pull out so far that rope stops with a jerk as this will cause rope failure. Do not allow rope and handle to snap back into place. 3. After two or three full firm pulls on recoil (or as soon as engine fires), move speed control to run position. 4. Operate a new engine at intermediate speeds and light load for the first few hours as you would a new automotive engine. 5. To stop engine, move speed control lever on engine to STOP position. 6. If carburetor needs adjustment to start or for operation, see “Carburetor Readjustment'’ section. SELF PROPELLED MODEL 1. Place drive engagement lever in the neutral position (towards the operator). 2. Move throttle control lever on handle to START position. 3. Crank engine. Pull recoil with a quick firm pull. Do not pull out so far that rope stops with a jerk as this will cause rope failure. Do not allow rope and handle to snap back into place. ADJUSTMENTS HEIGHT ADJUSTMENT Standing on the right hand side of vacuum move the index handle towards the left. Move handle towards rear of unit to lower height. Move the handle forward to raise the height. I IF VOU WRITE TO US ABOUT THiS ARTICLE OH IF YOU ORDER REPLACEMENT PARTS AL WAVS MENTION THIS MODEL « SERIAL NO MODEL 240-670A 240-680A NOTE: The Vacuum Bag has an air escape located on the upper right hand side. This should be open when the bag becomes half full. EXPLODED VIEW OF UPPER HANDLE 6 PARTS LIST FOR MODELS 240-670A AND 240-680A REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 720-0142 Grip (680A) 2 710-0606 Hex Bolt 1/4-20x1.50” Lg.* (680A) 3 711-0596 Conirol Rod (680A) 4 736-0108 FI. Wash. .510” I.D. x .75” O.D. (680A) 5 711-0179 Adj. Ferrule (680A) 6 712-0107 Hex Center L-Nut 1/4-20 Thd. (680A) 7 736-0173 Flat Wash. .28” I.D. x .75” O.D. x .063 8 710-0289 Hex Bolt 1/4-20x.50” Lg.* 9 731-0404 Air Duct 10 13316 Air Duct Liner 11 710-0106 Hex Bolt V4-20 x 1.25” Lg.* 12 12234 Upper Handle 13 712-0107 Hex Center L-Nut 1/4-20 Thd. 14 764-0127 Vacuum Bag 15 12104 Deflector 16 712-0107 Hex Center L-Nut 1/4-20 Thd. (680A) 17 746-0202 Throttle Control Ass’y.— Comp. (680A) 18 710-0606 Hex Bolt V4-20 x 1.50” Lg.* (680A) 19 748-0210 Spacer (680A) 20 12226 Control Lever(680A) 21 746-0229 Conduit and Wire 23 731-0344 Plastic Label *For faster service obtain standard nuts, bolts and washers locally. If these Items cannot be obtained locally, order by part number and size as shown on parts list. (488—Mack Truck Yellow) When ordering parts, if color or finish is important use the appropriate color code shown above, (e.g. Mack Truck Yellow Finish—12236(438).) NOTE: The engine is not under warranty by the vacuum manufacturer.. .If repairs or service is needed on the engine, please contact your nearest authorized engine service outlet. Check the “Yellow Pages” of your telephone book under “Engines—Gasoline.” Find It Fast In The Yellow Pages NOTE This instruction manual covers various models and all specifications shown do not necessarily apply to your model. Specifications subject to change without notice or obligation. 7 240-670A 240-680A NOTE Cable clip must be assembled to lower handle as shown, with open end towards the engine. This will prevent wear to the bag NOTE See differential breakdown Page 5 60 92 9l 90 59 93----5^ 94---7—' --- 87 86 EXPLODED VIEW OF FRAME PARTS LIST FOR MODELS 240-670A AND ...
Эта инструкция также подходит к моделям:Газоноуборщики - 240-680A (1.64 mb)