Poulan PRO 7349 Statesville Road Charlotte, NC 28269 545167664 Rev. 3 6/15/10 BRW ENGLISH ESPANOL FRANCAIS IDENTIFICATIONOFSAFETYSYMBOLSIDENTIFICATIONOFSAFETYSYMBOLS WARNING:Thisunitcanbedangerous!Carelessorimproperusecancauseseriousinjury. Readtheoperator’smanualbeforeuse.Failuretofollowinstructionscouldresultinseriousinjury.Saveoperator’smanual. Hazardzoneforthrownobjects. SBladecanthrowobjectsviolently. SYouandotherscanbeblinded/injured. SKeepchildren,bystanders,andanimals50feet(15meters)away

S Wear hearing protection. S Never start or run inside a closed room or building. Breathing exhaust fumes can kill. S Keep handles free of oil and fuel. S Keep hands and feet away from cutting area. S Never direct discharge of material toward bystanders nor allow anyone near the area of operation. Use care in directing discharge to avoid glass enclosures, automobiles, and the like. FUEL SAFETY (for gas powerheads) S Mix and pour fuel outdoors. S Keep away from sparks or flames. S Use a container

If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If plug does not fit fully into the wall outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord re

Should you experience any problems you can not easily remedy, please contact your nearest au tho rized service center/ department. They have com pe tent, well trained tech ni cians and the proper tools to service or repair this unit. Please read and retain this manual.The in struc tions will enable you to assemble and main tain your Grass Catch er properly. Always observe the "SAFETY RULES". TABLE OF CONTENTS SAFETY RULES.........................................................2-3 CUSTOMER RESPO

• If the grass catcher fails to pick up cut grass or leaves, it is an indication that clogging has occurred in the system or that the grass catcher containers are full. a. Disengage blades, shift into neutral, en ga ge the parking brake and stop the engine. -Raise seat. Unlatch and raise cover. -Slide out containers and dispose of clippings . -Replace containers, close cover, and latch. b. Unlatch chutes and check for clogging -Remove all debris in chutes. - Reassemble and latch chutes c. Check

• Your bagger is equipped with a dump bag indicator. As the bags become full, the flow indicating ball will drop down in its slot, indicating that the bags are full or the chutes have become clogged. Care should be taken not to damage the parts and that the ball moves freely at the beginning of each use. NOTE: To help prevent clogging of chutes, check/empty bags when ball begins to drop down in the slot. Experience will teach you the best time to empty the bags. • If the grass catcher fails to p

CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. ASSEMBLY MOWER DECK BAFFLE (See Fig. 1) Use Hardware - - GRO

ALIGNMENT MARKS 02085 COVER SEAL FIG. 3 7 SUPPORT POST (See Fig. 4) Use Hardware - - GROUP "C" CAUTION: Container sup port is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. 1. Rotate cover assembly onto its side as shown. 2. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. 02091 LOCKNUTS CARRIAGE BOLTS SUPPORT POST FIG. 4 5 5 MOUNTING TO TRACTOR (See Fig.

FIG. 13 1-1/8"2-3/4" 2-1/4" 3-3/8" 2" 1-7/16" Your drawbar may or may not have some or all of the holes shown. For the assembly of your new grass catcher only the five holes dimensioned will be used. If your drawbar does not have the five holes in the correct po si tions continue with this section. 1. Remove the drawbar by removing the two mounting bolts on each side. Keep hardware for remounting. NOTE: If your tractor has a wire loop mounted to the draw- bar, remove it at this time. 02349 DRAWB

Look carefully at the mower deck on your tractor and compare the deck mandrel to the illustrations below. If your mower deck mandrel looks like STYLE "A", your tractor is ready - proceed with the grass catcher assembly. If your mower deck mandrel looks like STYLE "B", go to the PREPARATION section in this manual. DECK MANDREL STYLE "B" DECK MANDREL STYLE "A" UPPER CHUTE GRASS CATCHER CONTAINERS LOWER CHUTE ATTACHING WING NUT W A R N I N G D o n o t o p e r a t e m o w e r u n l e s s c o n t a i