Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
SHOULDER BOLTS FIG. 1A TO REMOVE THE SUPPORT ASSEMBLY (See Fig. 1C) 1. Pull outward on the stop bracket enough to allow support assembly to be lifted up and away from drawbar. 2 FIG. 2 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 2) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor as shown. 2. Lift and rotate cover to align cover bracket with support assembly. 3. Slide cover assembly down onto the support assembly. 02646 COVER ASSEMBLY SUPPORT ASSEMBLY SUPPORT ASSEMBLY SUPPORT ASSEMBLY 6 WARNING Donotoperatemowerunlesscontainerisproperlyis subjecttowearanddetierioration.Check bagfrequently.Replacewhen crackedordamaged.Useonlya recommendedreplacementcontainer. WARNING 02082 CONTAINER MOUNTING (See Fig. 4) 1. Install one container to left side fi rst with warning to outside of unit. Install other container to right side. NOTE: Right con tain er should always over lap left con tain er at center sup port. 2. Close cover and lock latch handle over center support tube. 4 CENTER SUPPORT TUBE COVER LATCH HANDLE CONTAINER HANDLE CONTAINER WARNING FIG. 4 CONTAINER WARNING CONTAINER ASSEMBLY (See Fig. 3) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunlesscontainerisprope rlyissubjecttowearanddetierioration.Checkbagfrequ ently.Replacewhencrackedor damaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 3 3 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF LOWER CHUTE (See Fig. 5) 1. Lower mower deck to its lowest cutting position. NOTE: If equipped, remove mulch cover from mower deck and store in a safe place. 2. With your right hand, raise and hold deflector shield in upright position. 3. With your left hand, hold lower chute as shown and position lower rear edge of chute between gauge wheel bracket tab and mower housing, then carefully release deflector shield and hook rear latch to mower deck. 4. Raise deflector shield and align "B" on lower chute extended edge with "B" on mower housing. 5. With your right hand, push firmly on the lower chute until the extended edge slides under the defl ector shield and along side the hinge bracket as shown. 6. With chute in proper position, hold the chute securely, so it does not move, while hooking the front latch to the mower deck. NOTE: While hooking the latches, the deflector shield may try to push the chute away from the mower deck opening. It is important to hold the chute in position while hooking the latches to the mower deck. • If your tractor is equipped with gauge wheels on the deck, then it will be necessary to hook the rear latch into the hole in the R.H. gauge wheel bracket. CAUTION: Do not remove discharge guard from mower. Raise and hold guard when attaching lower chute and allow it to rest on chute while in operation. DEFLECTOR SHIELD HINGE BRACKET BBBB02558 ALIGN CHUTE "B" WITH MOWER "B" OPTIONAL GAUGE WHEEL AND BRACKET PUSH IN PLACE LOWER REAR EDGE BETWEEN GAUGE WHEEL BRACKET TAB AND MOWER HOUSING, THEN HOOK REAR LATCH WHEEL GAUGE WHEELS 02445 BREAR LATCH REAR GAUGE BRACKET DEFLECTOR SHIELD FRONT LATCH REAR LATCH WITHOUT WITH REAR GAUGE WHEELS EXTENDED EDGE "B" Must be under defl ector shield and along side the hinge bracket FIG. 5 7 8 02098 02099 UPPER CHUTE (See Figs. 6A & 6B) 1. Lower mower deck to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover. NOTE: Handle carefully so as not to damage dump bag in di ca tor. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with alignment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. 6 DUMP BAG HANDLE INDICATOR UPPER CHUTE COVER LOWER CHUTE FIG. 6A BOSSES LATCH PIN ALIGNMENT SLOT RUBBER LATCH FIG. 6B LEVEL MOWER DECK Be sure deck is properly leveled for best mower per for - mance. See your tractors owner's manual for instructions. 7 OPERATION TIPS FOR IMPROVED BAGGING OPE RATION: Follow the mower operation instructions in your tractor owner's manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total time of op...
Эта инструкция также подходит к моделям:Газонокосилки - 954 04 05-10 (744.42 kb)