Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Replace all worn or damaged decals. SAFETY INFORMATION 7 STRAP LANYARD SUPPORT BRACKET ASSEMBLY Collection System Tools Required Ratchet Torque Wrench ." Wrench ." Socket 9/16" Wrench 9/16" Socket 5/8" Socket 1. Open the mounting kit box and remove all of the components. 2. Place the support bracket on the frame and secure with (2) 539 990563, 3/8 x 1 bolts and (2) 539 976979, 3/8 nyloc nuts. 3. Place the hitch brackets on the frame and secure with (3) 990622, . x 1. bolts and (3) 539 101331, . nyloc nuts. 4. Place the hitch assembly on the ground behind the mower. Place the (2) hitch pins thru the hitch and the hitch brackets. Secure the hitch pins with the (2) hairpins that are secured with the (2) lanyards. 5. Install the two (2) straps on the hopper with ." bolts and nuts. Install the two (2) support brackets on the frame. 6. Attach hose support rod to the right side of the unit to keep the right rear tire from rubbing the hose. HITCH BRACKET SUPPORT BRACKET HITCH ASSEMBLY LANYARD HITCH PIN . ." Socket Flat Screw Driver 5/32" Allen Wrench Hacksaw 11/32" Drill Bit Drill 8059-009 8059-010 8059-011a ASSEMBLY Handle Assembly 1. Attach backing plate and tube support to hopper 3. Attach threaded rod to hopper and handle. When using holes shown in illustration. connected, adjust threaded tube using adjusting nuts at both ends. The adjustment will be 2. Connect handle to tube support using pivot pin. complete when handle is pulled forward and hopper door is fully closed. 4. Adjust handle stop so it goes over the center. BACKING PLATE HOLES BACKING PLATE TO HOPPER UNIT TUBE SUPPORT STOP PIVOT PIN THREADED TUBE HANDLE ADJUSTMENT NUT ROD END ADJUSTMENT NUT ROD END HOPPER FRAME 9 ASSEMBLY Hopper Door Adjustment Adjust door rods on both sides with adjusting nut so door closes evenly. See illustration. DOOR RODS ADJUSTMENT NUTS HOPPER DOOR HOPPER Blower Kit Install Blower Kit per the instructions shipped with the blower unit. (114992 for the 52" or 130195 for the 60".) Operating the Collection System 1. NEVER USE THE COLLECTION SYSTEM WITHOUT THE BLOWER ASSEMBLY AND HOSES SECURELY ATTACHED. 2. Make sure hoses are connected at both ends. Inspect hoses prior to each use. 3. Do not use the unit on slopes greater than 10 degrees. 4. The mower must be running in order to vacuum debris through the mower deck. 5. In heavy grass it may be necessary to mow and collect at a slower ground speed. 6. Never attempt to unclog the collection system until the mower’s engine has been shut off and all moving parts have come to a complete stop. 7. Do not stand behind the vent at the rear of the collection system due to the potential for small pieces of blowing debris to escape through the vent. 8. Wear eye and ear protection. 8059-013 SERVICE AND MAINTENANCE Transport Storage 1. Clean machine. 2. Cover all scratches with touch-up paint. WARNING 3. Covered or indoor storage is recommended. The collection system hopper must be completely empty while driving forward onto a trailer. If the mower must be loaded onto a trailer while there is still debris in the container, the mower must be backed up onto the trailer to avoid tipping. Cleaning and Washing Regular cleaning, washing, and lubricating will prolong the service of the machine. NOTE: Use care with power washers to avoid damage to decals. Limit direct spray on these items. DO NOT EXCEED 1000 PSI WATER PRESSURE FOR CLEANING. For best results, clean polymesh inside hood regularly. Instructions for doing this can be found in the Service section of this manual Preventative Maintenance Schedule Item Before Each Use Every 5 Hours Every 25 Hours Every 50 Hours Inspect/Clean Poly Mesh X X Check/Tighten Nuts & Bolts X Check/Tighten Hoses X Turn Hose End to End X Rotate Hose X Clean Machine X SERVICE AND MAINTENANCE Caring For Hoses 1. Inspect hoses before each use. If hoses have excessive wear, tears, or punctures, replace immediately. 2. To prolong the life of the hose, periodically rotate hose and turn hose end to end. Refer to Preventative Maintenance Schedule in this manual. 3. Avoid twists and sharp turns in the hoses, as they will increase wear on the hoses. 4. Avoid dragging the lower hose along the sides of buildings or other hard surfaces. Troubleshooting Guide Cleaning Poly Mesh The poly mesh on the collection system is located inside the container hood. For best results, clean poly mesh regularly. DO NOT USE THE COLLECTION SYSTEM WITHOUT POLY MESH SECURELY IN PLACE. DANGER Before servicing unit, wait for all moving parts to come to a complete stop. Turn engine off and remove the spark plug wire. PROBLEM Loss of Vacuum. POSSIBLE CAUSE Blower, hose or hood inlet clogged. Hopper full. Fan blades bent or broken. Poly mesh plugged. CORRECTION Remove hose and clean inlet. Inspect and empty. Replace/repair impeller. Clean poly mesh. Unusual vibration or noise Solid object jammed in unit. Loose or missing bolts on unit. Bent or damaged fan. Check and remove any obstruction. Tighten or repla...
Эта инструкция также подходит к моделям:Газонокосилки - DFS 114883 (389.04 kb)