Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Release lever to lock seat in position. Fig. 2 NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other peo ple and objects. TO ROLL TRACTOR OFF SKID (See Op er a tion section for location and function of con trols) • Raise attachment lift lever to its highest po si tion. • Release parking brake by de press ing clutch/brake ped al. • Place freewheel control in "trans mis sion dis en gaged" position (See “TO TRANS PORT” in the Op er a tion section of this manual). • Roll tractor forward off skid. Continue with the instructions that follow. TO INSTALL MOWER AND BLADE DRIVE BELT (See Figs. 3 - 16) 1. SET PARKING BRAKE LEVER AND LOWER ATTACHMENT LIFT LEVER (See Fig. 3 and 4) • Depress clutch/brake pedal all the way down and hold. • Pull parking brake lever up and hold, re lease pres sure from clutch/brake pedal, then release parking brake lever. Pedal should re main in brake position. Ensure parking brake will hold tractor secure. PARKING BRAKE LEVER Fig. 3 CAUTION: Lift lever is spring loaded. Have a tight grip on lift lever, lower it slowly and engage in lowest position. Lift lever is located on left side of fender. A ASSEMBLY 7 3. TURN STEERING WHEEL LEFT AND POSITION MOWER (See Fig. 6) • Turn steering wheel to the left as far as it will go and position mower on right side of tractor with deflector shield (Q) to the right. TRANSAXLE 02965 FRONT BACK ENGINE Q. DEFLECTOR SHIELD Q Fig. 6 90° END INTEGRATED WASHER END ANTI-SWAY BAR (S) TOWARDS TOWARDS TRANSAXLE MOWER DECK • From right side of mower, first insert 90° end of anti-sway bar (S) into hole in transaxle bracket (T), located near left rear tire in front of transaxle. NOTE: Flashlight may be helpful. 5. INSTALL ANTI-SWAY BAR (S) (IF EQUIPPED) (See Fig. 9 - 11) Fig. 9 02965 A. MOWER SIDE SUSPENSION ARMS Q. DEFLECTOR SHIELD Q A Fig. 8 4. SLIDE MOWER UNDER TRACTOR (See Fig. 8) • Bring belt forward and check belt for proper routing in all mower pulley grooves. NOTE: Be sure mower side suspension arms (A) are pointing forward before sliding mower under tractor. • Slide mower under tractor until it is centered under tractor. LIFT LEVER Fig. 4 H. FRONT MOWER BRACKET W. FRONT GAUGE WHEEL X. SHOULDER BOLT Y. 1-1/4 O.D. WASHER Z. 3/8-16 LOCKNUT Fig. 5 Z Y H W X Fig. 7 2. ASSEMBLE FRONT GAUGE WHEEL (W) TO FRONT OF MOWER (See Fig. 5) A. MOWER SIDE SUSPENSION ARMS B. RETAINER SPRING C. REAR LIFT LINK(S) D. RIGHT SIDE REAR MOWER BRACKET E. FRONT LIFT LINK ASSEMBLY F. FRONT SUSPENSION BRACKET H. FRONT MOWER BRACKET I. LEFT SIDE REAR MOWER BRACKET K. BELT TENSION ROD L. LOCKING BRACKET M. ENGINE CLUTCH PULLEY Q. DEFLECTOR SHIELD S. ANTI-SWAY BAR W. FRONT GAUGE WHEEL E A M F B K C C S W H Q I D L ASSEMBLY 8 6. ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 12) • Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B). • Repeat on opposite side of tractor. D A B A. MOWER SIDE SUSPENSION ARMS B. RETAINER SPRING D. RIGHT SIDE REAR MOWER BRACKET Fig. 12 NOTE: Depending on model, bracket (T) may be different than shown but hole for anti-sway bar will be in same position/location. ANTI-SWAY BAR (S) LOCATION TRANSAXLE BRACKET (T) LOCATED BETWEEN REAR TIRES PLACE 90° END INTO HOLE S T S. ANTI-SWAY BAR T. TRANSAXLE BRACKET Fig. 10 8 ATTACH FRONT LINK (E) (See Fig. 14) • Turn steering wheel to position wheels straight forward. • From front of tractor, insert rod end of front link (E) through front hole in tractor front suspension bracket (F). • Move to left side of mower and and insert large retainer spring (G) through hole in front link (E) behind front suspension bracket (F). • Insert other end of link (E) into hole in front mower bracket (H) and secure with washer and small retainer spring (J). NOTE: Requires deck lifting. Fig. 14 FRONT LINK LOCATION G E F M E. FRONT LIFT LINK ASSEMBLY F. FRONT SUSPENSION BRACKET G. LARGE RETAINER SPRING H. FRONT MOWER BRACKET J. SMALL RETAINER SPRING M. ENGINE CLUTCH PULLEY J H Fig. 13 7. ATTACH REAR LIFT LINKS (C) (See Fig. 13) • Insert rod end of rear lift link (C) into hole (U) in tractor lift shaft suspension arm and pivot link down to mower. • Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with large washer and large retainer spring. • Repeat on opposite side of tractor. C. REAR LIFT LINK(S) D. RIGHT SIDE REAR MOWER BRACKET U. HOLE D C U S D T D. RIGHT SIDE REAR MOWER BRACKET S. ANTI-SWAY BAR T. TRANSAXLE BRACKET Fig. 11 • Pivot the integrated washer end of anti-sway bar (S) towards mower deck bracket on right side of mower. Insert integrated washer end of bar into hole in rear mower bracket (D). Mov...