Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
Call Homelite customer service for assistance. The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1. SAVE ThESE INSTRUcTIONS Page FEATURESELEcTRIcAL DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three- wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. WARNING: The double insulated system is intended to protect the user from shock resulting from a break in the tool’s internal insulation. Observe all normal safety precautions to avoid electrical shock. NOTE: Servicing of a product with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the product to your nearest authorized service center for repair. Always use original factory replacement parts when servicing. ELEcTRIcAL cONNEcTION This product has a precision-built electric motor. It should be connected to a power supply that is 120 volts, Ac only (normal household current), 60 hz. Do not operate this product on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the product does not operate when plugged into an outlet, double-check the power supply. EXTENSION cORDS See Figure 1. When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the product will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Laboratories (UL) should be used. When working outdoors with a product, use an extension cord that is designed for outside use. This type of cord is designated with “WA” on the cord’s jacket. A proper extension cord is available at an authorized service center. It is possible to tie the extension cord and power cord in a knot to prevent them from becoming disconnected during use. Make the knot as shown in figure 1, then connect the plug end of the power cord into the receptacle end of the extension cord. This method can also be used to tie two extension cords together. Fig. 1 **Ampere rating (on product data plate) 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 cord Length Wire Size (A.W.G.) 12.1-16.0 25' 16 16 16 16 14 14 50' 16 16 16 14 14 12 100' 16 16 14 12 10 — **Used on 1 gauge - 0 amp circuit. NOTE: AWG = American Wire Gauge WARNING: Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools, or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury. WARNING: Check extension cords before each use. If damaged replace immediately. Never use the product with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury. Page Page FFEEAATTUURREESS PRODUCT SPECIFICATIONS Weight........................................................................................................................................................................ 14.6 lbs. Input......................................................................................................................................120 V, AC only, 60 Hz, 12 Amps Blade Length..................................................................................................................................................................... 8 in. Fig. 2 SWITCH TRIGGER ADJUSTABLE FRONT HANDLE BLADE edgerguard REAR HANDLE adjusting knob lock-off BUTTON wheelS CORD RETAINER handlep ole SPRING ASSIST FRONT WHEEL CleanEdge™ blower powerheadp ole FEATURES KNOW yOUR EDGER /TRENchER See Figure . The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules. Cleanedge™ BLOWER The CleanEdge™ blower, at the base of the edger, is designed to blow debris from the blade area while edging paved surfaces. cORD RETAINER A convenient cord retainer helps keep the extension cord connection secure during tool operation. FRONT hANDLE For ease of operation, the edger is equipped with a front handle. LAWN EDGING AND TRENchING The edger blade can be...