Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Make certain all parts and literature have been removed before the carton is discarded. 2. Extend the throttle control which is attached to the mower and place on the floor. Be careful not to bend or kink control wire. ‘3. Place lower handle in position over weld pins in handle mount brackets on deck. Secure by placing two hairpin cotters (E) in inner hole on weld pins. See figure 2. NOTE It may be necessary to bend the ends of the lower handle inward slightly to assure a snug fit against the bracket mounting area. Outer Hole (For Storage) Inner Hole (For Operation) ......... NOTE There are two (2) holes in the handle mount brackets. Place hairpin cotter in the inner hole for operation. The outer hole is for storage. See figure 3. FIGURE 3. 4 FIGURE 4. 4. There are two height positions for the handle. Place upper handle in position over lower handle, selecting hole for either high or low posi- _tion. Refer to figure 20. Secure with two curved carriage bolts (B) and handle knobs (A) as shown in figure 4. The knobs can be either to the inside or the outside of the handle. 5. Place the throttle control in position on the left hand side of the upper handle. Secure with hex bolt (C) and hex lock nut (D) provided. See figure 5. NOTE Reference to left or right side of machine is from operator’s position at the handle facing forward. FIGURES. Cable Tie (F) FIGURE 6. 6. Secure throttle control cable to handle with — cable ties (F) provided. See figure 6. 7. Check all nuts and bolts for correct tightness. 5 r}^,_v I /♦ Upper Frame——A -Lower Frame Ass’y. ^ I ASSEMBLY Grass Catcher The grass catcher is partially assembled. See 'figure 7. Grass Bag FIGURE 7. FIGURE 8. Rear Frame Threaded -I«- . Bag Ends of' Rear Frame FIGURE 9. _Z_ After threading, both ends of upper frame should be inside the bag. See figure 9. 6 Lower Frame Assembly Upper Frame 3. Place the upper frame over the lower frame assembly as shown in figure 10. NOTE Figure 10 was photographed with bag off frame for clarity. FIGURE 10. 1 Bottom of Bag 'Frame Plastic Channels FIGURE 11. Grass Catcher Frame 4. Secure bag to frame by slipping plastic channels on bag over frame. See figure 11. 5. Close top of bag by stretching loose material over the end of frame. TO ATTACH BAG TO MOWER t WARNING J 2. FIGURE 12. DO NOT operate the mower with the — chute door open unless the complete grass catcher is properly mounted on the mower. Attach the grass catcher frame to grass catcher hitch bracket on rear of the mower by hooking grass catcher into hooks on grass catcher hitch bracket. See figure 12. Lift the rear of grass catcher up. The roller on the grass catcher will push the chute door on the mower open. See figure 12. 7 NOTE Figure 12 is shown with the chute door open for photo clarity only. 3. Move the locking lever forward and hook in slot on mower. See figures 13 and 14. FIGURE 13. ß^0j$ I, if',: ■' *■ TO REMOVE GRASS CATCHER 1. To remove the grass catcher, lift the rear of grass catcher, push forward and unhook locking lever. 2. Lift off grass catcher. See figure 15. 8 OPERATION DO NOT OPERATE THIS MOWER WITH THE CHUTE DOOR OPEN, UNLESS THE COMPLETE GRASSCATCHER IS PROPERLY MOUNTED ON THE MOWER. FIGURE 16. Keep hands and feet away from the chute area on cutting deck. See figure 16. HI^NOTE For shipping purposes your mower is set with the wheels in a low cutting height position. For best results, raise the cutting position until it is determined which height is best for your lawn. See adjustment section. BEFORE STARTING 1. Check to see that the handle is in the operating detent in the brackets on the deck, and the upstop projections restrict the handle from moving up and forward. If necessary, remove the left side from the mounting pin on the deck bracket. Push inward to decrease the spacing between the two sides of the handle until it is slightly less than the spacing of the deck brackets. Reinstall over the mounting pin and secure the hair cotter pin in the inner holes. 2. Fill sump with oil, using a high quality detergent oil classified “For Service SC, SD, SE or MS.” Use SAE 30, SAE 10W-30 or SAE 10W-40 viscosity grade oil. Nothing should be added to the recommended oil. Place engine level. Remove oil fill plug. See figure 17. Fill to point of overflowing. Pour slowly. Capacity 11/4 pints. FIGURE 17. 3. Fill fuel tank, using clean, fresh, lead-free or leaded “regular” grade automotive gasoline. Fill tank completely. DO NOT MIXOIL WITH GASOLINE. TO START ENGINE 1. Move throttle control lever to “START” position. 2. Place foot on right side of deck and hold handle to prevent tipping the unit. Grasp starter handle and pull out rapidly. Return it slowly to the engine. Repeat if necessary. ^■^NOTE This engine features a unique Automatic Choke. In case of flooding, move control to “STOP” and pull starter six times. Then move control to “START” position and start engine. If...