Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
With the engine running only at idle, attach the power tool to the spring hook of your harness (see appropriate chapter of this manual). Working Conditions Operate and start your power tool only outdoors in a ventilated area. Operate the edger under good visibility and daylight conditions only. Work carefully. ! Warning! Your edger produces toxic exhaust fumes as soon as the engine is running. These gases ( e.g. carbon monoxide) may be colorless and odorless. To reduce the risk of serious or fatal injury from inhaling toxic fumes, never run the edger indoors or in poorly ventilated locations. ! Warning! Use of this product can generate dust and fumes containing chemicals known to cause respiratory disease, cancer, birth defects, or other reproductive harm. If you are unfamiliar with the risks associated with the particular dust or fume at issue, consult your employer, governmental agencies such as OSHA and NIOSH and other sources on hazardous materials. The State of California and some other authorities, for instance, have published lists of substances known to cause cancer, reproductive toxicity, etc. Control dust and fumes at the source where possible. In this regard use good work practices and follow the recommendations of OSHA/NIOSH and occupational and trade associations. When the inhalation of toxic dust and fumes cannot be eliminated, the operator and any bystanders should always wear a respirator approved by NIOSH/MSHA for the type of dust and / or fumes encountered. FCS-KM English / USA ! Warning! Never divert discharge of material toward bystanders nor allow anyone near the area of operation. Use care in directing discharge to avoid glass enclosures, automobiles, and the like. 002BA117 KN Always hold the power tool firmly with both hands. Wrap your fingers tightly around the handles, keeping the handles cradled between your thumb and forefinger. Keep your hands in this position to have your power tool under control at all times. Make sure your edger handles and grips are in good condition and free of moisture, pitch, oil or grease. ! Warning! Never attempt to operate any edger with one hand. Loss of control of the edger resulting in serious or fatal injury may result. 002BA057 KN ! Warning! Do not overreach. Keep proper footing and balance at all times. Special care must be taken in slippery conditions (wet ground, snow) and in difficult, overgrown terrain. Watch for hidden obstacles such as tree stumps, roots and ditches to avoid stumbling. Be extremely cautious when working on slopes or uneven ground. ! Warning! Before cutting, inspect the area for stones, glass, pieces of metal, trash or other solid objects. The cutting attachment could throw objects of this kind. Remove such objects if possible, and avoid any remaining ones when cutting. Use only for edging in grass, weeds and soft green plants. Do not use edger on gravel surfaces. ! Warning! To reduce the risk of injury from thrown objects and blade contact, never operate an edger without a properly mounted deflector. Keep the skirt on the deflector adjusted properly at all times (see chapter on mounting the cutting tool of your owner’s manual). Do not overreach. Keep proper footing an balance at all times. FCS- KM English / USA To reduce the risk of injury from blade contact, keep hands and feet away from cutting area. ! Warning! This edger is normally to be used at ground level with the cutting attachment perpendicular to the ground. Use of an edger above ground level or with the cutting attachment parallel to the ground may increase the risk of injury, since the cutting attachment is more fully exposed and the edger may be more difficult to control. Never use your edger as a hedge trimmer. ! Warning When using your edger, avoid cutting close to fences, sides of buildings, tree trunks, stones or other such objects that could cause the edger to kick out or could cause damage to the blade. In addition, be alert to an increased risk of ricochets in such situations. If the edger strikes a foreign object, follow these steps: stop the engine, disconnect spark plug lead, inspect for damage and repair any damage before restarting and operating the product. Do not operate using the starting throttle lock as you do not have control of the engine speed. See section of your CombiEngine owner's manual on the proper use of the slide control. If the cutting tool or deflector becomes clogged or stuck, always turn off the engine and make sure the cutting tool has stopped before cleaning. Grass, weeds, etc. should be cleaned off the cutting tool at regular intervals. ! Warning! During cutting, check the tightness and the condition of the cutting tool at regular intervals. If the behavior of the tool changes, stop the engine immediately, and check the nut securing the tool for tightness and the cutting tool for cracks and damage. Replace cracked, bent, warped, damaged or dull cutting tools immediately. Such tools may shatter at high speed and cause serious or...