Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
1.6 RIDING ATTACHMENTS Use only Exmark riding attachments. The use of other than Exmark riding attachments may create a hazardous condition resulting in injury. 1.7 SAFETY SIGNS 1.7.1 Keep all safety signs legible. Remove all grease, dirt, and debris from safety signs and instructional labels. 1.7.2 Safety signs must be replaced if they are missing or illegible. 1.7.3 When new components are installed, be sure that current safety signs are affixed to the replaced components. 1.7.4 New safety signs may be obtained from your authorized Exmark equipment dealer or distributor or from Exmark Mfg. Co. Inc. 1.7.5 Safety signs may be affixed by peeling off the backing to expose the adhesive surface. Apply only to a clean, dry surface. Smooth to remove any air bubbles. 1.7.6 Familiarize yourself with the following safety signs and instruction labels. They are critical to the safe operation of your Exmark commercial mower. - 7 - 8 - Decals for ECS Handle units only: Decals for Pistol Grip Handle units only: Decals for all units: PART NO. 103-1541 LOCATION: Console PART NO. 1-303508 LOCATION: On Top RH Surface of Mower Deck PART NO. 1-303517 LOCATION: LH Side of Rear Surface of Engine Deck PART NO. 103-2242 LOCATION: LH Side of Console PART NO. 103-2243 LOCATION: RH Side of Console PART NO. 103-5354 LOCATION: Console PART NO. 1-303102 LOCATION: Upper Handles - 9 - PART NO. 1-403005 LOCATION: LH & RH Front Top Surface of Mower Deck PART NO. 1-403143 LOCATION: RH Rear Surface of Engine Deck PART NO. 1-513747 LOCATION: Top Rear of Battery Cover PART NO. 1-513746 LOCATION: Surface of Engine Deck Next to Muffler PART NO. 1-553049 LOCATION: On Top Front LH Surface of Mower Deck PART NO. 1-323540 LOCATION: Front of Mower Deck Top Surface PART NO. 1-413214 LOCATION: Right Side of Hydro Control Crank Arm PART NO. 1-523552 LOCATION: On Top of Hydraulic Tank PART NO. 103-1077 LOCATION: On Top Front RH Surface of Mower Deck PART NO. 98-5954 LOCATION: Under LH, RH & Center Belt Shields PART NO. 103-2432 LOCATION: Parking Brake Lever - 10 - 2. SPECIFICATIONS 2.1 MODEL NUMBER: TT23KCC; TT23KAC; TT20KC 2.2 ENGINE 2.2.1 Engine Specifications: See your Engine Owner's Manual. 2.2.2 3600 RPM (No Load). 2.3 FUEL SYSTEM 2.3.1 Capacity: 5.0 gal. (18.9 L.) 2.3.2 Type of Fuel: Regular unleaded gasoline, 87 octane or higher. In countries using the research method, it should be a 90 octane minimum. 2.3.3 Fuel Filter: Replaceable in-line 2.3.4 Fuel Shut-Off Valve: 1/4 turn 2.4 ELECTRICAL SYSTEM: 2.4.1 Charging System: Flywheel Alternator 2.4.2 Charging Capacity: 15 amp 2.4.3 Battery Type: BCI Group U1 235 amps at O° F 2.4.4 Battery Voltage: 12 Volt; Polarity, negative ground. 2.4.5 Fuses: blade type, 20 amp to charging circuit; 20 amp to electric clutch. 2.4.6 Safety Interlock System: Operator must have OPC (Operator Presence Control) levers held in contact with handle grips, speed control lever in neutral, and PTO disengaged to start engine. Release of OPC levers will cause the engine to stop if speed control lever is not in neutral and/or PTO is engaged. Park brake must be disengaged to move speed control out of neutral or engine will kill. 2.5 STEERING CONTROL: Fingertip drive control levers provide independent speed control, braking and neutral to each drive wheel for moving forward or reverse, stopping, and power turning. 2.6 TRANSMISSION: 2.6.1 Two Hydro Gear BDP-10A variable displacement piston pumps independently coupled to two high efficiency Parker wheel drive motors. 2.6.2 Hydraulic Oil Type: Mobil 1 15W-50 2.6.3 Hydraulic Oil Capacity: 2.4 qt. (2.2 L.) 2.6.3 Hydraulic Filter is replaceable cartridge type. P/N 1-513211: 10 microns, 18 psi bypass (Summer use above 32° F (0° C)) P/N 1-523541: 40 microns, 18 psi bypass (Winter use below 32° F (0° C)) 2.6.4 Speed Range: Forward 0 - 6.75 mph (10.9 km/h) Reverse 0 - 2.25 mph (3.6 km/h) PART NO. 103-4935 LOCATION: Left Rear Top Corner of Engine Deck PART NO. 103-2239 LOCATION: Top of Mower Deck Beneath Center Shield 2.6.5 Drive wheel release valves allow machine to be moved when the engine is not running 2.7 WHEEL DRIVE SYSTEM: Drive wheels are direct coupled to Parker wheel drive motors with 1.0" (25.4 mm) tapered shaft. 2.8 TIRES Drive Front Caster Size .......................... 18 x 8.50-8..........................11 x 4.0-5 Quantity............................2........................................ 2 Tread........................Turf Master...........................Smooth Ply Rating.........................4........................................4 Pressure................14 psi (90 kPa)..................16 psi (152 kPa) 2.9 MOWER DECK 2.9.1 Model Numbers: FMD604 and FMD524 2.9.2 Cutting Width: 60 in. (152.4 cm.) 52 in. (132.1 cm.) 2.9.3 Discharge: Right Side 2.9.4 Optional Mulch Kit and Bagger available. 2.9.5 Blade Size: 60" - (3 ea.) 20.50 in. (52.1 cm.) 52" - (3 ea.) 18.00 in. (45.7 cm.) 2.9.6 Type of Drive: Electric clutch mounted on engine shaft. Blades driven by two belts with...