Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Replace paper cartridge every 100 hours of operation or every season, whichever occurs first. Service air cleaner more often under dusty condi tions. 1. Loosen screws and remove cover. 2. Carefully remove cartridge. 3. Clean by gently tapping on a flat surface. If very dirty, replace cartridge. _kCAUTION: Petroleum solvents, such as kerosene, are not to be used to clean cartridge. They may cause deterioration of the cartridge. Do not oil cartridge. Do not use pressurized air to clean or dry cartridge. 4. Install cartridge, then replace cover. i Base MUFFLER Inspect and replace corroded muffler as it could create a fire hazard and/or damage. SPARK PLUG Replace spark plug at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the "PRODUCT SPECIFICATIONS" section of this manual. CLEANING IMPORTANT: For best performance, keep mower housing free of built-grass and trash. Clean the underside of your mower after each use. fler on startup. 15 _I,CAUTION: Disconnect spark plug wire If no leaks are present, start engine (as from spark plug and place wire where it described in the Operation section of this cannot come in contact with plug. • Clean the underside of your lawn mower by scraping to remove build-up of grass and trash. • Clean engine often to keep trash from accumulating. A clogged engine runs hotter and shortens engine life. • Keep finished surfaces and wheels free of al! gasoline, oil, etc. • We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in shortened engine life. WATER WASHOUT FEATURE Your lawn mower is equipped with a fitting that allows quick and easy cleaning of the underside of the housing. To use this feature, proceed as follows: 1. Move lawn mower to an area of cut grass or another hard surface. NOTE: Water, grass and other debris will drain from beneath the mower housing during the washout process. 2. Remove grass catcher and discharge chute assembly from lawn mower. 3. Close mulcher door (if equipped). 4. Connect a garden hose to the fitting where shown. IMPORTANT: Be sure the garden hose is not routed under the lawn mower housing or entangled in the wheels. 5. Turn on water supply and check for leaks at the fitting. manual) and let engine run until the underside of the lawn mower is clean. ,i& WARNING: Do not engage the drive system during the washout process. 6. Shut off the engine. 7. Shut off water supply and remove hose from fitting. CAUTION: Do not remove hose from fitting while engine is running. Water in engine can result in shortened engine life. 8. Start engine (as described in the Operation section of this manual) and let engine run for a full minute to remove excess water from mower. Hose Fitting CLEAN UNDER DRIVE COVER Clean under drive cover at least twice a season. Scrape underside of cover with putty knife or similar tool to remove any build-up of trash or grass on underside of drive cover. WARNING: To avoid serious injury, before performing any service and adjustments: 1. Release control bar and stop engine. 2. Make sure the blade and all moving parts have completely stopped. 3. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. LAWN MOWER TO REMOVE DRIVE BELT TO ADJUST CUTTING HEIGHT 1. Disconnect spark plug wire from spark See "TO ADJUST CUTTING HEIGHT" in plug and place wire where it cannot come in contact with plug. the Operation section of this manual. 2. Remove screws retaining drive cover REAR DEFLECTOR and remove drive cover from lawn The rear deflector, attached between the mower housing (See Figure A). rear wheels of your mower, is provided to minimize the possibility that objects will be thrown out of the rear of the mower into the operator mowing position. If deflector becomes damaged, it should be replaced. 16 Lawn mower housing Drive cover Figure A . Remove drive cable from anchor, then detach it and return spring from idler arm assembly (See Fig. B). ,_./Drive cable Housing __ anchor holeff'--3 7. Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth. 8. Remove blade bolt. 9. Remove blade, attaching hardware (bolt, lock washer and hardened washer), blade adapter and debris shield as one assembly. 10. Remove drive belt from blade adapter and debris shield; discard old belt. TO REPLACE DRIVE BELT 1. Place new drive belt in the belt retainer of the debris shield. Be sure to route belt between belt keepers and through slot (See Figure D). Belt retainer, Tab Belt kee Drive belt / _'_._` c:_,,_ Idler arm Driv Drive Return i_h ,,'_ assembly pulley belt spring "'.':-::i/PIVOT Figure B 4. Pivot idler arm assembly to slacken drive belt, then remove drive belt from drive pulley, bel...