Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Spark plug type and gap setting are shown in the "PRODUCT SPECIFICATIONS" section of this manual. IMPORTANT: For best performance, keep mower housing free of built-grass and trash. Clean the underside of your mower after each use. ,I&CAUTION" Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. • Clean the underside of your lawn mower by scraping to remove build-up of grass and trash. • Clean engine often to keep trash from accumulating. A clogged engine runs hotter and shortens engine life. • Keep finished surfaces and wheels free of al! gasoline, oil, etc. • We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in shortened engine life. CLEAN UNDER DRIVE COVER Clean under drive cover at least twice a season. Scrape underside of cover with putty knife or similar tool to remove any build-up of trash or grass on underside of drive cover. 16 A WARNING: To avoid serious injury, before performing any service and adjustments: 1. Release control bar and stop engine. 2. Make sure the blade and all moving parts have completely stopped. 3. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. LAWN MOWER TO ADJUST CUTTING HEIGHT See "TO ADJUST CUTTING HEIGHT" in the Operation section of this manual. REAR DEFLECTOR The rear deflector, attached between the rear wheels of your mower, is provided to minimize the possibility that objects will be thrown out of the rear of the mower into the operator mowing position. If the deflector becomes damaged, it should be replaced. TO REMOVE DRIVE BELT 1. Remove drive cover and belt keeper. 2. Remove belt from gearcase pulley. 3. Turn lawn mower on its side with air filter and carburetor down. 4. Remove blade and blade adapter. 5. Remove belt from engine pulley. Drive cover \ Gearcase pulley Belt 3er J Belt TO REPLACE DRIVE BELT 1. Place new drive belt on engine pulley, inside tabs of belt retainer. 2. Route the other end of the new drive belt through hole in housing. 3. Reinstall blade adapter and blade. 4. Return mower to upright position. 5. Install new belt on gearcase pulley. 6. Reinstall belt keeper and drive cover. NOTE: Always use factory approved belt to assure proper fit and long life. Blade adapter Key Crankshaft Lockwasher Blade ...... o / Blade bolt Hardened ,, '_ washer Trailing/edge retainer TO ADJUST HANDLE The handle on your lawn mower has three (3) height positions -adjust to height that suits you. 1. Remove knob and carriage bolt on one side of the lower handle. 2. While holding handle assembly, remove knob and carriage bolt from opposite side, align hole in handle with desired hole in handle bracket and reassemble bolt and knob and tighten securely. 3. Align opposite side of handle with same positioning hole and secure with bolt and knob. Handle bracket Knob Bolt 17 ENGINE ENGINE SPEED Your engine speed has been factory set. Do not attempt to increase engine speed or it may result in personal injury. If you believe that engine is running too fast or too slow, take your mower to a Sears or other qualified service center for repair and adjustment. CARBURETOR Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your lawn mower to a Sears or other qualified service center for repair and/or adjustment. IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact a Sears or other qualified service center, which has proper equipment and experience to make any necessary adjustments. Immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more. LAWN MOWER When lawn mower is to be stored for a Operator MOWING POSITION period of time, clean it thoroughly, remove control bar all dirt, grease, leaves, etc. Store in a clean, dry area. 1. Clean entire lawn mower (See "CLEANING" in the Maintenance section of this manual). .o o /:% 2. Lubricate as shown in the Maintenance FORWARD / Uppersection of this manual. FOR handle 3. Be sure that all nuts, bolts, screws, and STORAGE pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. Handle knob 4. Touch up all rusted or chipped paint surfaces; sand lightly before painting. Lower handle HANDLE You can fold your lawn mower handle for storage. Handle 1. Loosen the two (2) handle knobs on bracket sides of the upper handle and allow handle to fold down to the rear. 2. Remove the two (2) handle knobs and Knob carriage bolts on sides of the lower handle and pivot entire handle as-Bolt sembly forward and allow it to rest on mower. 3. Reinstall knobs and carriage bolts to...