Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
The further toward the handle the lever is pulled, the faster the unit will travel. . Forward motion will stop when either the operator presence control bar or drive control lever are released. To stop forward motion without stopping engine, release the drive control lever only. Hold operator presence control bar down against handle to continue mowing without self-propelling. NOTE: If after releasing the drive control the mower will not roll backwards, push the mower forward slightly to disengage drive wheels. Operator presence control bar Drive control DRIVE CONTROL ADJUSTMENT Over time, the drive control system may become "loose", resulting in decreased speed. There is a turnbuckle on the drive control housing to increase tension on the drive cable. Proceed as follows: 1. Turn unit off and disconnect spark plug wire from spark plug. 2. Rotate turnbuckle on drive control to increase drive speed. 3. Operate mower to test drive speed. Readjust as required. 4. If condition fails to improve after the above steps (forward speed remains the same), your drive belt is worn and should be replaced. Adjustment turnbuckle TO ADJUST CUTTING HEIGHT Raise wheels for low cut and lower wheels for high cut, adjust cutting height to suit your requirements. Medium position is best for most lawns. • To change cutting height, pull up on adjuster lever, move wheel up or down to suit your requirements and release adjuster lever. Be sure all wheels are in the same setting. NOTE: Adjuster is properly positioned when lever inserts into hole in plate. LEVER BACKWARD 4 i TO LOWER MOWER Plate TO ENGAGE DRIVE lever DRIVE CONTROL LEVER CONTROL DISENGAGED FORWARD 8 TO RAISE MOWER TO CONVERT MOWER Your lawn mower was shipped ready to be used as a mulcher. To convert to bagging or discharging: REAR BAGGING • Lift rear door of the lawn mower and place the grass catcher frame hooks onto the grass bag brackets. • To convert to mulching or discharging operation, remove grass catcher and close rear door. door bag bracket Grass catcher handle Full bac catcher indicator frame hook window NOTE: Rear door will remain open until operator presence control bar is held down to the handle. AI_CAUTION: Do NOT force rear door to close. Serious damage to your mower could result. I \ \ Unlock latch Open mulcher door Discharge deflector \ I I SIDE DISCHARGING • Rear door must be closed. • Open mulcher door and install discharge deflector under door as shown. • Mower is now ready for discharging operation. • To convert to mulching or bagging operation, discharge deflector must be removed and mulcher door must be closed and locked. SIMPLE STEPS TO REMEMBER WHEN CONVERTING YOUR LAWN MOWER FOR MULCHING 1. Rear door closed. 2. Mulcher door closed and locked. FOR REAR BAGGING 1. Grass catcher installed. 2. Mulcher door closed and locked. FOR SIDE DISCHARGING 1. Rear door closed. 2. Discharge deflector installed. ,ACAUTION: Do not run your lawn mower without rear door closed or approved grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or propped open. 9 TO EMPTY GRASS CATCHER Empty the grass catcher when clippings are visible in the full bag indicator window. 1. Lift up on grass catcher using the frame handle. 2. Remove grass catcher with clippings from under lawn mower handle. 3. Empty clippings from bag using both frame handle and bag handle. NOTE: Do not drag the bag when emptying; it will cause unnecessary wear. Grass catcher frame Bag handle BEFORE STARTING ENGINE ADD OIL Your lawnmower is shipped without oil in the engine. For type and grade of oil to use, see "ENGINE" in the Maintenance section of this manual. _, CAUTION: DO NOT overfill engine with oil, or it will smoke heavily from the muffler on startup. 1. Be sure lawnmower is level. 2. Remove oil dipstick from oil fill spout. 3. You receive a container of oil with the unit. Slowly pour the entire container down the oil fill spout into the engine. NOTE: Initial oi! fill requires only 18 oz. due to residual oil in engine from the manufacturers 100% quality testing. When changing oil you may need 20 oz. 4. Insert and tighten dipstick. IMPORTANT: • Check oil level before each use. Add oil if needed. Fill to full line on dipstick. • Change the oil after every 25 hours of operation or each season. You may need to change the oil more often under dusty, dirty conditions. See "TO CHANGE ENGINE OIL" in the Maintenance section of this manual. Engine oil cap Gasoline filler cap ADD GASOLINE . Fill fuel tank to bottom of tank filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel fresh- Bess. A CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. • i, CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and for...