Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
The BEST method of handling the ground speed control levers is in three steps -as shown in Figure 7. FIRST place your hands onto the levers as shown. SECOND, to go forward gradually push the levers forward with your palms. THIRD, to speed up move the levers farther forward. To slow down smoothly, slowly move the levers back toward neutral. Figure 7. Move Control Levers Gradually Forward Travel Practice Gradually move both ground speed control levers evenly FORWARD from neutral (see Figure 8). Slow down and repeat. Reverse Travel Practice LOOK DOWN & BEHIND, then gradually move both ground speed control levers evenly BACK from neutral (see Figure 9). Slow down and repeat. NOTE: Practice backing up for several minutes before attempting to do so near objects. The rider turns as sharply in reverse as when going forward, and backing up straight takes practice. Reverse Travel Figure 8. Forward Travel Figure 9. Reverse Travel 18 Practice Turning Around a Corner Practice Turning In Place While traveling forward allow one handle to gradually To "zero turn" means to turn in place. To turn in place, return back toward neutral (see Figure 10). Practice sev-gradually move one ground speed control lever forward eral times before mowing. from neutral and one lever back from neutral simultane ously (see Figure 11). Repeat several times. NOTE: To prevent damaging your lawn by pivoting directly on the tire tread, it is best to keep both wheels going at least slightly forward. Executing Turns Turning In Place / Figure 10. RightTurn Figure 11. Turning in Place ADVANCED DRIVING Executing an End-Of-Row Zero Turn Your zero turn rider's unique ability to turn in place allows you to turn around at the end of a cutting row rather than having to stop and make a Y-turn before starting a new row. For example, to execute a right end-of row zero turn: , Slow down at the end of the row. 2. Move the LEFT ground speed control lever forward slightly while moving the RIGHT ground speed control lever back to center and then slightly back from center (see Figure 12). Be sure to keep both wheels moving to avoid turf damage. 3. Begin mowing forward again. This technique turns the rider RIGHT and slightly overlaps the row just cut -eliminating the need to back up and re-cut missed grass. As you become more familiar and experienced with operating the zero turn rider, you will learn more maneuvers that will make your mowing time easier and more enjoyable. Remember, the more you practice, the better your control of the rider will be! Figure 12. Executing an End-Of-Row Turn 19 MOWER DECK REMOVAL & INSTALLATION NOTE: Perform mower removal and installation on a hard, level surface such as a concrete floor. WARNING After lowering the mower cutting height, engage parking brake, turn off the mower blades, turn the ignition switch to STOP, and remove key before attempting to install or remove the mower. Removing the Mower Deck 1. Turn the mower blades OFF, put the ground speed control levers in START/PARK position, engage the parking brake, turn the ignition OFF, and wait for all moving parts to stop. 2. Pivot the front wheels forward. 3. Use the mower belt release lever (D, Figure 13) to release belt tension. Remove the mower belt (B) from engine pulley (A). 4. Turn the ignition switch from OFF to RUN without starting the engine. 5. Use the mower cutting height switch to raise the mower deck. 6. Place 4x4 wood blocks under the front and rear lip of the mower deck to securely support it. 7. Use the mower cutting height switch to fully lower the mower so that is it resting on the 4x4 wood blocks (A, Figure 14). 8. Turn the ignition switch to OFF and remove the key. 9. Remove the hair pin clip (B) securing the rear mower lift arm. Separate the lift arm from the mower deck. Repeat on both sides of the mower. 10. Remove the 3/8 -16 x 3/4 carriage bolts and flange nuts (C) that secure the front hitch rod, then remove the hitch rod (D). 11. Slide the mower deck out from under the rider. Installing the Mower Deck 1. Slide the mower deck under the right side of the rider. Slide the mower forward and hook the front hitch rod (D, Figure 14) to the front mower deck hooks. 2. Secure front hitch rod with two 3/8 -16 x 3/4 carriage bolts and flange nuts (C). 3. Slide the mower deck backwards and connect the rear lift arms to the mower deck. Secure with hair pin clips (B). 4. Insert the key into the ignition switch. Turn the switch from OFF to RUN without starting the engine. 5. Use the cutting height switch to raise the mower until it is no longer resting on the 4x4 wood blocks (A). 6. Turn the ignition switch OFF and remove the key. Remove the 4x4 blocks. 7. Use the mower belt release lever (D, Figure 13) to release mower belt tension, and install the belt as shown. Figure 13. Mower Belt Routing A. Engine Pulley B. Mower Belt C. Idler Pulleys D. Mower Belt Release Lever E. Arbor Pulleys Figure 14. Mower Hitch Components A. 4x4 Wood Blocks B. Hair Pin Clip C. 3/8-16 x 31...
Эта инструкция также подходит к моделям:Газонокосилки - 107.289860 (8.5 mb)