Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
15 1. ENGINE: For complete maintenance and operating infor- mation for your engine, please refer to your engine operating and maintenance instructions furnished by the engine manufacturer and included in your Zero Turn mower information packet. NOTE Air intake screen must be kept clean. If plugged, engine may be seriously dam- aged by over heating. 2. TACHOMETER / HOURMETER (Optional) The tachometer / hourmeter includes a FlashAlert feature to remind you to change engine oil and filter at recommended inter- vals. The tachometer displays engine rpm when the engine is running and elapsed time in hours when the engine is turned off. Oil Change Flash Alert -Break-in interval at 5 hours with 1 hour before and after flash. Normal interval at 50 hours with 2 hour before and after flash. 3. BATTERY: When taking the battery out of the mower for servicing, make sure to reconnect the cables to the battery exactly as they were prior to removal. Keep the battery clean. Remove the corrosion around the battery terminals by applying a solu- tion of one part baking soda to four parts water. Coat all exposed terminal surfaces with a light layer of grease or petroleum jelly to prevent corrosion. NOTE At temperatures below 32 degrees F (0 deg C) the full charge state must be maintained to prevent cell electrolyte from freezing and causing permanent battery damage. 4. TIRES: Correct tire pressure is essential for efficient operation of the mower. Check tire air pres- sure periodically. Inflate front and rear tires to 15 psi. Lug bolts should be checked regularly for tightness. Torque lug bolts to 59 ft./lbs. 5. MOWER BLADES: Check sharpness of mower blades after every 10 hours of operation. To sharpen blades proceed as follows: WARNING WHEN IT IS NECESSARY TO RAISE THE DECK OR MOWER FOR SERVICE OR MAINTENANCE, TO AVOID SERIOUS INJURY OR DEATH, STOP ENGINE, SET PARKING BRAKE, REMOVE IGNI- TION KEY AND SPARK PLUG WIRES AND SECURELY SUPPORT THE DECK OR MOWER BEFORE WORKING UNDERNEATH. A. Lift deck and secure in raised position. B. Remove bolt, cup washer, and blade from shaft. C Blades should be discarded when worn exces- sively. See sketch. New Blade 30 Degrees When Notch Starts Dangerous! Discard Blade D. Sharpen blade with a hand file, electric grinderor blade sharpener. Wear gloves and eye protection when sharpening. Grind blade at original bevel. E. Check balance of blade by positioning the blade on a nail or blade balance pedestal. Grind the blade on the end that is heavier until both sides balance. F. Install blades with the concave side of the cup washer against blade. Be sure blades are installed with uplifts and cutting edges in the proper directions. Tighten retaining bolt to 76 ft./lbs. WARNING AVOID SERIOUS INJURY OR DEATH: P llTHE BATTERY CONTAINS SULFURIC ACID. AVOID CONTACT WITH SKIN, EYES OR CLOTHING. EYES -FLUSH WITH WATER AND GET PROMPT MED- ICALATTENTION. ANTIDOTE: INTERNAL -DRINK LARGE QUANTITIES OF WATER OR MILK. FOLLOW WITH MILK OF MAG- NESIA, BEATEN EGG OR VEGETABLE OIL. CALL A PHYSICIAN IMMEDIATELY. P llBATTERIES PRODUCE EXPLOSIVE GASES. KEEP SPARKS, FLAMES AND SMOKING MATERI- ALS AWAY. VENTILATE WHEN CHARGING IN AN ENCLOSED SPACE. WEAR EYE PROTECTION WHEN WORKING NEAR BATTERIES. P ll KEEP OUT OF REACH OF CHILDREN. WARNING WHEN IT IS NECESSARY TO RAISE THE DECK OR MOWER FOR SERVICE OR MAINTENANCE, TO AVOID SERIOUS INJURY OR DEATH, STOP ENGINE, SET PARKING BRAKE, REMOVE IGNI- TION KEY AND SPARK PLUG WIRES AND SECURELY SUPPORT THE DECK OR MOWER BEFORE WORKING UNDERNEATH. 6. CLEANING GRASS BUILD UP UNDER DECK Depress the deck lift foot pedal and lock in position, then move the height adjustment pin to the 4-1/2” position. Lift the front of the unit and support unit securely. Clean out any grass build up from underside of deck and in deck discharge chute. 16 MOTION CONTROL STEERING ADJUSTMENT 1. Raise the drive wheels of the Zero Turn off of the ground. Safely block the frame in this position so it is secure. This adjustment must be made with the drive wheels turning. 2. Remove the electrical connection from the seat switch and temporarily install a jumper wire across the terminals of the wiring harness. 3. Loosen the jamnuts on the hex turnbuckle, which connects the lever control arm to the pump control arm. Note: The nuts to the front of the hex turnbuckle have lefthanded threads. 4. Start the engine. Run the engine at full throttle and release brake. 5. Position the control levers in the neutral position. If the drive wheels creep (rotate) in the neutral position then lengthen or shorten the turnbuckle assembly. Make the adjustment to stop the wheel from rotating. 6. Re-tighten the nuts at the end of the hex turnbuckles and repeat the procedure for the opposite side of the unit. 7. Shut the unit off. Remove the jumper wire from the wiring harness and replace the connectors into the seat switch. Never operate the mower unless all safety switches are operating properly. DRIVE ADJUSTMENTS Steering and motion c...