Войти:
Оценок - 2, средний балл: 4.5 ( )

Инструкция по эксплуатации Bush Hog, модель 300 Series

Производитель: Bush Hog
Размер: 266.69 kb
Название файла: d823a882-2d03-55f4-05df-a509667428ea.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Make sure everyone is clear of machinery before starting the engine, engaging power, or operating the machine. EMPLOYEE TRACTOR OPERATING INSTRUCTIONS: 1. Securely fasten your seat belt if the tractor has a 5. Watch where you are going, especially at row ROPS. ends, on roads, and around trees. 2. Where possible, avoid operating the tractor near 6. Do not permit others to ride. ditches, embankments, and holes. 7. Operate the tractor smoothly - no jerky turns, 3. Reduce speed when turning, crossing slopes, and starts, or stops. on rough, slick, or muddy surfaces. 8. Hitch only to the drawbar and hitch points recom- 4. Stay off slopes too steep for safe operation. mended by tractor manufacturers. 9. When tractor is stopped, set brakes securely and use park lock if available. Child Labor Under 16 Years Old Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.) 5 SPECIFICATIONS MODEL SIZE TYPE HITCH HUBS SPOONS APPROX. WT. PG-300 30” Pull 4 32 175 lbs. PG-480 48” Lift 6 48 290 lbs. PG-600 60” Lift 8 64 350 lbs. PG-720 72” Lift 10 80 390 lbs. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Figure 1 PG-720 PluggerTop LinkLift PointLower Lift PointParking StrandMast Greasable Shaft SleeveSpoonsWeight Rack SECTION I OPERATION WARNING DURING IMPLEMENT ADJUSTMENT KEEP BODY, HANDS AND FEET CLEAR OF SPOONS OR FRAME. ATTACHMENT (Lift Type) The implement should be placed on level ground. Place the tractor rockshaft control in “position con- trol” (non-floating) for attaching and detaching the implement. “Draft control” or “position control” can be used while operating. Back the tractor until the ends of the lift arms can be attached to the lift points on the implement. Secure the lift arms to the mast. (Figure 1) Attach the center link to the top of the mast and adjust so that the frame will be level in the operating position. Remove parking stand and store in the upside down position. DETACHING FROM TRACTOR Pin parking stand into position and lower the imple- ment to the ground with rockshaft control in position control. Remove top link from mast, disconnect hitch arms from bottom pins and pull tractor away from implement. 6 Figure 2Lift Type PluggerFigure 3 PG-300Pull Type PluggerGrease Before Each UseWeight BoxesFigure 4Optional Slicing KnivesKnives should beassembled to outsidesof hub plates, onalternating sides. Figure 2Lift Type PluggerFigure 3 PG-300Pull Type PluggerGrease Before Each UseWeight BoxesFigure 4Optional Slicing KnivesKnives should beassembled to outsidesof hub plates, onalternating sides. OPERATION Level the implement from side to side and front to rear using adjustments on the tractor’s 3-point lift. WARNING DURING IMPLEMENT ADJUSTMENT KEEP BODY, HANDS AND FEET CLEAR OF SPOONS OR OTHER PARTS. Weight may be added to the plugger frame to aid in penetrating hard soil. Concrete blocks, water jugs or other types of weight may be used as long as noth- ing extends through the frame and interferes with the rotation of the spoons. Penetration should be approximately one to 1-1/2”. (Figures 2 & 3) By removing core plugs from the soil, lawns are bet- ter able to breath and hold moisture. Compacted soil and thatch are relieved, allowing air and fertilizer to reach roots. Optional slicing knives are available to replace spoons on the mounting plates. Four knives per hub are used to cut grass runners which causes new growth and thicker lawns. Install as shown. (Figure 4) Care should be exercised during use of the plugger to prevent hanging the spoons on immovable objects or otherwise use the implement under conditions beyond its designed capacity. TRANSPORTATION CAUTION WHEN EQUIPMENT IS TRANSPORTED, USE NECESSARY DEVICES REQUIRED BY LOCAL REGULATIONS FOR ADE- QUATE WARNING TO OPERATORS OF OTHER VEHICLES. SECTION II MAINTENANCE LUBRICATION -Apply NLGI Grade 2 multi-purpose grease to sleeves on shaft before each use. (Figure 2) Tighten all other fasteners to specifications given in torque chart. CAUTION LOWER THE IMPLEMENT AS MUCH AS POSSIBLE AND SECURELY SUPPORT BEFORE MAKING ANY ADJUSTMENT. Inspect your implement periodically and replace any worn or broken parts in order to have it ready for use when needed. When spoons become worn, replace one at a time to ensure proper location and assembly. Store the implement out of the weather when it is not in use. This helps prevent rusting of the spoons and other components. 7 SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damages can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information. 8 TORQUE ...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории