Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
STEP 3: (SEE FIGURE 4) Place plug on a work bench or solid table and push end of bumper down onto plug. Repeat for remaining plugs. STEP 4: (SEE FIGURE 5) Place a washer onto a carriage bolt and then insert the bolt into the second mounting hole from the front of the tractor frame. Securely tighten a whizlock nut onto the bolt on the outside of the tractor frame. Repeat on other side of tractor. HARDWARE SHOWN FULL SiZE EXCEPT WHERE NOTED (not full size) PARTS BAG "A" FIGURE 2 Ref. A B C D Part 43350 44072 R19171616 47674 66460 Qty. 4 4 4 4 1 Description Carriage Whizlock Washer, Plug Bumper Bolt, 3/8-16 x 1" Nut, 3/8" 1/2"xl" REMOVE FRONT SCREWS REMOVE BROWNING SHIELD FIGURE BUMPER PUSH DOWN WiTH EVEN PRESSURE WORK BENCH OR SOLID TABLE I CARRIAGE BOLT AND WASHER \ Call 1-866-576-8388 for missing DO NOT RETURN TO STORE parts or assembly help WHIZLOCK NUT FIGURE 5 3 STEP 5: (SEE FIGURE 6) * Spread ends of bumper enough to fit slots onto bolts in rear mounting holes in tractor frame. * The bumper has three mounting holes. The rear holes provide the most clearance while the forward holes provide a neater appearance. Use a hole that provides enough clearance for the hood to stay in raised position when opened. Place a washer onto a carriage bolt and insert the bolt through the tractor frame and into desired mounting hole on each side of bumper. Secure with a whizlock nut. iMPORTANT: Before fully tightening nuts, be sure tractor hood will stay in raised position when opened. STEP 6: (SEE FIGURE 7) * Replace the browning shield using the front screws you removed in Step 2. CARRIAGE BOLT AND WASHER WHIZLOCK NUT FIGURE 6 REPLACE FRONT SCREWS REPLACE BROWNING SHIELD FIGURE 7 4 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE iNSTRUCTiONS FOR DUAL SUSPENSION BRACKET TRACTORS STEP 1: (SEE FIGURE 2) * Open parts bags labelled "A" and "B" and verify that all parts needed are present. NOTE: Place cardboard or a mat on work surface to prevent scratching of parts removed from carton and tractor. NOTE: Not all hardware will be used. Unused parts may be discarded after assembly STEP 2: (SEE FIGURE 3) e Remove tractor hood. (Refer to tractor manual.) e Remove an (LT) Lawn Tractor heat shield like the one shown. Remove a (GT) Garden Tractor heat shield like the one shown only if you need access to inside of tractor frame during step 5. iMPORTANT: Be sure to re-attach the heat shield after bumper is installed. HARDWARE SHOWN FULL SiZE EXCEPT WHERE NOTED Ref. Part Qty. Description A 48894 2 Self Threading Bolt, 3/8-16 x 1-1/2" B 43062 2 Hex Bolt, 3/8-16 x 1-1/2" C 43001 4 Hex Bolt, 3/8-16 x 1" D 44072 4 Whizlock Nut, 3/8" E 43003 4 Lock Washer, 3/8" F 47674 4 Plug 65932 1 Bumper (LT) LAWN TRACTOR REMOVE THIS STYLE HEAT SHIELD (GT) GARDEN TRACTOR REMOVE THIS HEAT SHIELD ONLY IF MUFFLER MUST BE MOVED IN STEP 4. Call 1-866-576-8388 for missing DO NOT RETURN TO STORE parts or assembly help jFIGORE 3 STEP 3: (SEE FIGURE 4) * Place plug on a work bench or solid table and push end of bumper down onto plug. Repeat for remaining plugs. STEP 4: (SEE FIGURE 5) * Remove any bolts present in front mounting holes in side of tractor frame. If bolt will not screw out of hole, check if a nut is present on bolt on inside of frame. On GT tractors, if access to nut is blocked by a front mounted muffler, slide muffler down exhaust tubes to rest on top of browning shield. iMPORTANT: Be sure to re-attach muffler and heat shield after bumper is installed. • If rear mounting holes in tractor frame are empty, install hex bolts and whizlock nuts supplied in the parts bags. See figure 5. BUMPER PUSH DOWN WITH EVEN PRESSURE WORK BENCH SHORT STEP OR SOLID TABLE I ,_'_ PLUG (E_-_ ) FIGURE4 (LT) LAWN TRACTOR REMOVE BOLT iNSTALL (C), (D) IF iF PRESENT HOLE iS EMPTY SUSPENSION BRACKET / (LT) LAWN TRACTOR REMOVE BOLT INSTALL(C), (D) IF IF PRESENT HOLE IS EMPTY SUSPENSION BRACKET (GT) GARDEN TRACTOR EXHAUSTTUBES MUFFLER \/ BROWNING SHIELD / REMOVE BOLT SUSPENSION BRACKET IF PRESENT FIGURE 5 6 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE STEP 5: (SEE FIGURE 6) * Spread ends of bumper enough to fit slots onto bolts in rear mounting holes in tractor frame. * The bumper has three mounting holes. The rear hole provides the most clearance while the forward holes provide a neater appearance. Use a hole that provides enough clearance for hood to stay in raised position when opened. Attach the bumper using either standard hex bolts and whizlock nuts or self threading bolts and lock washers. Use the self threading bolts if standard hex bolts do not insert freely into the hole in the tractor frame. iMPORTANT: Before fully tightening bolts, be sure tractor hood will stay in raised position when opened. LAWN TRACTOR (LT) SHOWN GARDEN TRACTOR (GT) iS SIMILAR WHIZLOCK NUT (D) FORBOLT(B) (E) FIGURE 6 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE Your Home For expert troubleshooting and h...