Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
486.245993, 486.24598 Fits 917 Series LT/YT/GT Tractors DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. • Safety • Assembly ,, Operation ,, Maintenance ,, Parts Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. PRINTED IN U.S.A. FORM NO. 40502 (REV. 1/07) ONEYEAR LIMITED WARRANTY When operated and maintained according to the instructions supplied with it, if this Tractor Brush Guard fails due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME ® to arrange for free repair. If this product is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179 Any power equipment can cause injuryif operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. Refer to your tractor owners manual for "Rules For Safe Operation". Look for this symbol to point out impo rtant safety precautions. It means --Attention!! Become alert!! Your safety is involved. HARDWARE -FULL SiZE D C (not full size) Ref. Part Qty. Description No. No. A 48894 2 Self Threading Bolt, 3/8-16 x 1-1/2" B 43062 2 Hex Bolt, 3/8-16 x 1-1/2 C 43001 4 Hex Bolt, 3/8-16 x 1" D HA21362 4 Nylock Nut, 3/8-16 E 44742 2 Plug F 43003 4 Lock Washer, 3/8" 65932 1 Bumper TOOLS REQUIRED (2) 9/16" Wrenches (Socket wrench may be used) Place cardboard or a mat on work surface to prevent scratching of parts removed from carton and tractor. Identify and lay out parts listed above. Not all hardware will be used. Unused parts may be discarded after assembly. SINGLE ROD DECK SUSPENSION TRACTORS iMPORTANT: If your tractor has a mower deck suspension bracket located under the middle of the front axle as shown in figure 1, continue with the instructions on page 3. If your tractor does not have a mower deck suspension bracket like the one shown go to page 4. MOWER DECK SUSPENSION BRACKET FIGURE 1 VIEWED FROM FRONT CAUTION!Muffleris hot!Allowengineto cool downbeforeproceedingwith bumperinstallation. STEP 1 : (SEE FIGURE 2) * Remove tractor hood. (Refer to tractor manual.) * Remove the browning shield as shown below. REMOVE FRONT SCREWS REMOVE BROWNING SHIELD FIGURE 2 STEP 2: (SEE FIGURE 3) * Insert a hex bolt (C) into the second mounting hole from the front of the tractor frame and fully tighten a hex nut (D) onto the bolt. Repeat on other side of tractor. HEX BOLT (C) \ HEX NUT (D) FIGURE 3 STEP 3: (SEE FIGURE 4) * Place plug (E) on a work bench or solid table and push end of bumper down onto plug. Repeat for second plug. BUMPER PUSH DOWN WITH EVEN PRESSURE WORK BENCH SHORT STEP OR SOLID TABLE PLUG (E) STEP 4: (SEE FIGURE 5) * Spread ends of bumper enough to fit slots onto bolts in rear mounting holes in tractor frame. * The bumper has three mounting holes. The rear hole provides the most clearance while the forward holes provide a neater appearance. Use a hole that provides enough clearance for hood to stay in raised position when opened. Insert a hex bolt (C) through tractor frame and into desired mounting hole on each side of bumper and secure with a hex nut (D). iMPORTANT: Before fully tightening nuts, be sure tractor hood will stay in raised position when opened. HEX BOLT (C) (D) / STEP 5: (SEE FIGURE 6) * Replace the browning shield using the front screws you removed in Step 1. / REPLACE FRONT SCREWS REPLACE BROWNING SHIELD FIGURE 6 FIGURE 4 3 DUAL ROD DECK SUSPENSION TRACTORS STEP 2: (SEE FIGURE 2) IMPORTANT: Thoso instructions are for tractors with dual ...
Эта инструкция также подходит к моделям:Газонокосилки - 486.245993 (442.48 kb)