Оценок - 3, средний балл: 3.7 ( )

Производитель: Dekko Размер: 2.62 mb Название файла: Язык инструкции:

Route the wire harness as shown on the adjacent photo and make the following connections: 1. The smaller, white, 2-pin connector is routed through a hole in the chassis and is connected to the blade activation safety switch 2-pin connector. 2. The larger, white, 5-pin connector is connected to the mating connector at the rear of the Honda engine. 3. The black wire is connected to a ground lug located on the back of the Honda engine. 4. The yellow wire is attached to the bottom of the starter motor solenoid on the Honda engine. In addition, the battery terminal wires must be connected to provide power to the electric starter. Attach the red and black battery terminal wires to the battery. Once all connections are made, the wire harness can be strapped into place permanently to the handle bars and chassis using the black wire-ties provided. For 36” Models The 36” models have the following connections: 1. The 36” hydro drive model has the same as “connection 1” for the 52” models discussed above, connecting the blade activation safety switch located underneath the front of the chassis. The wire harness is routed through a hole in the chassis as per the above diagrams. 2. For the belt drive 36” models, connect the blade activation safety switch located on the back of the chassis. It is a two pin connector coming from a black switch box under the fuel tank bracket. See adjacent photo. 3. There are 2 engine connections from the wire harness. A black wire that is attached to a ground lug on the engine and a red wire connector that is attached to the red wire crimp connector located at the rear of the Honda engine. The crimp on connector is typically covered with a green plastic sleeve. The red wire is the engine kill switch wire. Once all connections are made, the wire harness can be strapped into place permanently to the handle bars and chassis using the black wire-ties provided. 1 2 3 4 36” belt drive blade activation safety switch location top view. Black ground wire for Honda engine. Red wire with crimp connectors and typically a green plastic cover. DEK® is exclusively distributed by GXi International, LLC Rev: 8/2008 10 of 21 Heavy Duty Power Equipment 36B, 36BX, 36H, 36HX, 52H, 52HX Assembly Instructions Throttle cable clamp Step 4: Throttle and Choke Cable Connections On the 36” Honda powered models, there is one cable that functions as a throttle cable, a choke activation cable, and operates a kill switch. It is important that the cable be positioned correctly in the connector to permit all three functions. The throttle cable connector is located at the rear corner of the engine. Insert the throttle cable into the lower of the two holes, insert the cable into the cable clamp directly above the holes. Adjust the throttle cable positioning in the clamp to allow the choke lever to activate when the throttle on the control panel is on the top position. To make this adjustment you may be required to secure and tighten the cable clamp a few times as you adjust the cable positioning and test for choke activation. On the 52 Hydro models powered by Honda there are separate throttle and choke cables. Both are connected in the front center of the engine. The throttle cable is connected to the top lever in the front hole. The choke cable is connected to the lower lever. See attached picture. Ensure that the cables are clamped to provide full travel for the levers on the control panel. Right: 52” Mower Throttle and Choke Connections Throttle cable clamp Throttle cable connection Choke cable clamp Choke cable connection Step 5: Fuel tank connections WARNING: FUEL LEAKS OR A LOOSE FUEL TANK OR A LOOSE FUEL VALVE CAN LEAD TO SEVERE INJURY OR DEATH. ENSURE ALL CONNECTIONS ARE SECURE AND INSPECT THOROUGHLY FOR ANY POTETIAL LEAKS IN THE FUEL SYSTEM. IF YOU FIND A LOOSE CONNECTION OR A LEAK, MAKE AN IMMEDIATE REPAIR OR ASK FOR ASSITANCE FROM A PROFESSIONAL MECHANIC OR SERVICE CENTER. DO NOT OPERATE THIS LAWN MOWER IF ANY COMPONENT OF THE FUEL SYSTEM IS LOOSE OR LEAKS GASOLINE! Locate the fuel tank on the fuel tank bracket and align the fuel valve in the center of the clearance hole. Place the fuel tank straps into position, wrapping them around the tank and the bracket. Note: the 36B model has slots for the straps to feed through. Once the fuel tank and straps are in place, securely tighten the straps using the bolts provided. Once secure, firmly attach the fuel line to the fuel valve nipple. Ensure all connections are firm and secure. Tighten as required to make sure the fuel system is tightly attached. Choke lever motion Above: 36” Honda Mower Throttle and Choke Connection DEK® is exclusively distributed by GXi International, LLC Rev: 8/2008 11 of 21 Heavy Duty Power Equipment Operating Instructions 36B, 36BX, 36H, 36HX, 52H, 52HX Starting the Engine WARNING DANGER: DO NOT OPERATE THE ENGINE IN A CONFINED SPACE WHERE DANGEROUS CARBON MONOXIDE FUMES CAN COLLECT. CARBON DIOXIDE IS ODORLESS, TASTELESS AND CAN BE FATAL. NOTE: ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: