Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Pilot must match blade center hole for proper fit. 2. Place blade (E) over upper plate pilot and install the "lower plate" (F) and L.H. nut (G). Tri-Cut blade (H) is installed with glide cup (J). 3. Insert locking tool (K) through hole in upper plate and notch in gear housing (C) to prevent splined shaft from turning, tighten nut (G) and secure with a split pin (L). C A B H K D E J F G L K D 20 2020202020 E F G L IMPORTANT Never reuse a cotter pin - install a new cotter pin each time a blade is installed or replaced. 4. Remove locking tool. X7502233600 X750005530 01/03 INSTALL HARNESS CLAMP NOTE Some models require installation of harness clamp. If your unit does not have a clamp follow these directions. 1. Remove shield and gear housing as an assembly. a. Loosen two (2) screws (A) that clamp the gear housing to the shaft. b. Remove locating screw (B) found at the top of the gear housing. c. Pull shield and gear housing assembly from the drive shaft assembly. NOTE Prevent the flexible drive cable from sliding from the drive shaft housing. If cable does slide free, clean dirt from cable and re- lubricate with lithium based grease prior to re-assembly. 2. Remove front handle. a. Remove four (4) screws and nuts and back plate from handle. b. Remove handle. 3. Install clamp. a. Slightly spread clamp and carefully slide up drive shaft. b. Install harness ring using spacer and 5 x 18 mm bolt. c. Put on harness and attach unit to harness. Slide harness clamp up or down until unit balances with head approximately 50-75 mm (2 -3 in.) from the ground. d. Tighten harness clamp screw. INSTALL SHIELD AND GEAR HOUSING ASSEMBLY 1. Push gearbox assembly on end of drive shaft taking care to engage the drive cable with the gear housing. 2. Locate the gear housing on the drive shaft and install the locating screw (B). 3. Tighten the two (2) side clamping screws (A). INSTALL HANDLE/BARRIER BAR A A B NOTE The Barrier Bar is required when using blades. Units equipped with U-Handles do not require installation of the Barrier Bar. 1. Position front handle on shaft and install Barrier Bar using four (4) screws and nuts. 2. Position handle for comfortable operation, and tighten screws securely. NOTE The Barrier Bar is NOT A HANDLE and should not be gripped when using or carrying the unit. CONVERSION N/P 99944200416 Para los Modelos: SRM-230, 231, 260, 261 Numero de serie ALL ADVERTENCIA PELIGRO Para la operacion con hoja se requiere el uso de la arnes (no incluida en el kit) P/N C062000070 (Los E.E.U.U.) o N/P C062000060 (Canada). Esta ayuda a restringir y controlar el movimiento de la unidad en caso de un tiron, o atoro. La operacion con la hoja sin una correa puede dar lugar a lesiones serias. NOTA El uso de la arnes (no incluida) y este kit, permitira el uso con la hojas de metal o de nylon para cortar cesped/ hiervas. Todo otro uso de la hoja de metal requiere el kit del Mango en “U” y el uso de una arnes restrictiva. NOTA La barrera de barra es utilizada restrinja el...
Эта инструкция также подходит к моделям:Газонокосилки - BLADE CONVERSION KIT 260 (127.76 kb)
Газонокосилки - BLADE CONVERSION KIT 261 (127.76 kb)
Газонокосилки - BLADE CONVERSION KIT SRM-230 (127.76 kb)