Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Square Hole D. Shoulder Bolt, 5/16-18 E. Rear Frame Support B C D A A E Figure 3. Hitch Installation A. Hitch B. Shoulder Bolt C. Pin D. Hole in Draw Bar E. Hair Pin A B D E C Initial Installation HITCH INSTALLATION 1. Slide the 5/16-18 speed nut (A, Figure 1) onto rear frame support (E) through square hole (C) so that the threaded side (B) is on the inside of tractor. 2. Secure the 5/16-18 shoulder bolt (D) as shown. 3. Repeat on the other side. B C D A Figure 2. Frame Plate Reinforcement Installation A. Frame Reinforcement B. Rear Frame Support C. Frame Support Hole D. Capscrew, 5/16-18 x 1-1/4 (new) E. Locknut, 5/16-18 (existing) F. Capscrew, 5/16-18 (existing) 4. Remove existing nuts and capscrews from both sides and rear frame support holes (C, Figure 2) 5. Secure frame reinforcement (A) to the inside of the rear frame support (B) using new 5/16-18 x 1-1/4 capscrews (D) and existing 5/16-18 capscrews and locknuts (E & F) as shown. 6. Slide the hitch (A, Figure 3) on right side and left side shoulder bolt (B) while sliding pin (C) into hole (D) as shown. Secure with hair pin (E). C D E F 5 Tube Component Assembly Baffle Installation 1. Determine which baffle to use. See Figure 4 Chart. 2. Lift side discharge chute (H, Figure 4). 3. Insert baffle (F) through discharge opening and position baffle into place. 4. Tighten carriage bolts (A) and nuts (E) on baffle (F). 5. Tighten carriage bolt (B) and nut (E) on baffle (F). 6. Position baffle (G) into place. 7. Tighten carriage bolts (C) and nuts (E) on baffle (G). 8. Tighten carriage bolts (D) and nuts (E) on baffle (G). Figure 4. Baffle Assembly A. Carriage Bolts, 5/16-18 x 5/8 B. Carriage Bolt, 5/16-18 x 5/8 C. Carriage Bolts, 5/16-18 x 5/8 D. Carriage Bolts, 5/16-18 x 5/8 E. Locknut, 5/16-18 F. Right Hand Baffle G. Left Hand Baffle H. Discharge Chute E A F E E C E E B D G H “A” 44” Mower Deck 50” Mower Deck “A” RH side 26-1/4” long RH side 29-3/4” long “B” LH side 24-7/8” long LH side 27-3/4” long “B” 6 Component Installation Figure 6. Lower Chute to Boot Installation A. Pin, Latch B. Carriage Bolt, 1/4-20 x 5/8 C. Locknut, 1/4-20 D. Lower Chute E. Locknut, Center Lock, 5/16-18 F. Strap, Rubber G. Locknuts, Whiz Lock, 5/16-18 H. Rod, Boot Mount I. Capscrew, Hex Head, 5/16-18 x 1-1/4 J. Capscrew, Hex Head, Thin, 5/16-18 x 1 D C B F A G G H J I E LOWER CHUTE ROD AND PIN INSTALLATION 1. Insert the head of pin (A, Figure 6) through front hole of lower chute (D). Secure with 1/4-20 x 5/8 carriage bolt (B) and 1/4-20 lock nut (C) as shown. 2. Install the rod (H) to lower chute (D) using 5/16-18 x 1 capscrew (J) and 5/16-18 locknut (G) for front holes. Use 5/16-18 x 1-1/4 capscrew (I) and 5/16-18 locknut (G) as shown. Tighten hardware. 3. Install the rubber strap (F) onto capscrew (I) securing with 5/16-18 locknut as shown. Figure 7. Handle to Tube Installation A. Handle B. Locknuts, KEPS, 1/4-20 C. Screw, Slotted, 1/4-20 x 1/2 D. Screw, Slotted, 1/4-20 x 1 E. Strap, Rubber F. Locknut, Center Lock, 1/4-20 HANDLE INSTALLATION 1. Install handle (A, Figure 7) using 1/4-20 x 1/2 screw and 1/4-20 locknut (B) for rear hole. Use 1/4-20 x 1 screw (D) as shown. Tighten hardware. 2. Install strap (E) to screw (D) securing with 1/4-20 locknut (F). B D B F A E C Component Installation INSTALL MOUNTING PLATE 1. Install mounting plate (A, Figure 5) to mower deck as shown. Secure with 5/16-18 x 5/8 carriage bolts (C) and 5/16-18 locknuts (A). Figure 5. Install Mounting Plate A. Mounting Plate B. Locknuts, 5/16-18 C. Carriage Bolts, 5/16-18 x 5/8 C B A Install Upright Support & Bag Support Bracket 7 Figure 8. Install Upright Support A. Hitch B. Upright Support C. Capscrews, 3/8-16 x 1 D. Locknuts, 3/8-16 A INSTALL UPRIGHT SUPPORT TO HITCH 1. Install the upright support (B, Figure 8) to hitch (A) and secure with 3/8-16 x 1 capscrews (C) and locknuts (D) as shown. B INSTALL BAG AND COVER SUPPORT 1. Install the bag and cover support (B, Figure 9) to upright support (A) using reinforcement plate (C) and 3/8-16 x 1 capscrews (D) and 3/8-16locknuts (E) as shown. A C B Figure 9. Install Bag and Cover Support A. Upright Support B. Bag and cover Support C. Reinforcement Plate D. Capscrews, 3/8-16 x 1 E. Locknuts, 3/8-16 C D E D Cover and Bag Installation 8 Figure 10. Install Cover Assembly A. Bag Support Bracket B. Cover Assembly C. Cover Hinge Pins D. Hair Pins E. Hinge Pivots D INSTALL COVER ASSEMBLY 1. Attach cover assembly (B, Figure 10) to bag support bracket (A) using hinge pivots (E). Secure cover using cover hinge pins (C) and hair pins (D) as shown. INSTALL COLLECTOR BAGS 1. Raise the cover (A, Figure 11). 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). Note: It may be necessary to fold seat forward to allow cover to stay in the raised position. C E A B A D C B Figure 11. Install Collector Bags A. Cover B. Collector Bags C. Grass Bag Hanger D. Bag Hanger Post C D E 9 Tube Installation C D E A B Figure 12. Install Lower Tube A. Lower Chute Rod B. ...
Эта инструкция также подходит к моделям:Газонокосилки - 1695169 (767.61 kb)