Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
NOTE: Excessive roller chain tightness will shorten the life of the bearings. Chain(s) should have movement of 0.18 in./4mm free play back and forth at center point between front drive sprocket and rear tine assembly sprocket. ENGINE MAINTENANCE (Refer to engine manufacturer's owners manual) Check engine and gear reduction case oil level with engine resting in a level position. Inspect air filter element and replace if necessary. AERATOR STORAGE WARNING SAFETY WARNING: TO PREVENT POSSIBLE EXPLOSION OR IGNITION OF VAPORIZED FUEL, DO NOT STORE EQUIPMENT WITH FUEL IN TANK OR CARBURETOR OR NEAR OPEN FLAME (I.E. FURNACE, WATER HEATER, PILOT LIGHT). All Guards Must Be In Place While Machine Is In Operation STORAGE INSTRUCTIONS Before the Aerator is put into storage for any period exceeding 30 days, the following steps should be taken. 1. Drain all fuel from fuel tank and fuel lines. 2. Start engine and run until all fuel is used from carburetor float bowl. 3. While engine is still warm, drain the crankcase oil and replace with the proper weight oil corresponding to the season the Aerator will next be used. 4. Remove the spark plug and squirt a small quantity of engine oil into the cylinder. Turn the engine over a few times to distribute that oil. 5. Lubricate all lubrication fittings. To put Aerator into operation after an extended storage: 1. Check for loose parts and tighten if necessary. 2. Check for cracked or broken tines and replace. 3. Fill fuel tank. 4. Check engine and gear reduction case oil levels (with engine in a level position). 5. Start engine. 6. Check for fuel leaks. 7. Check operation of control handle(s) to make sure unit stops when lever is released forward. 8. Aerator is equipped with fuel shut-off valve, close valve before transporting. CA-18 COMPACT AERATOR (S.N. 1062 & UP) PARTS LIST Parts Main Frame CA-18 COMPACT AERATOR QTY/PER QTY/PER KEY PART NO. SHEET DESCRIPTION KEY PART NO. SHEET DESCRIPTION 1 400127 1 MAIN FRAME 24 400141 1 ARM, R.H. REAR AXLE SUPPORT 2 400138 1 PULLEY GUARD 25 500169 2 5/16" LOCK NUT 3 400131 1 HANDLE MOUNT 26 500149 2 1/2" x 2" BOLT 4 500129 8 3/8" NUT 27 500106 4 1/2" NUT 5 500130 6 3/8" LOCK WASHER 28 500006 2 1/2" LOCK WASHER 6 500043 4 3/8" x 1" BOLT 29 500011 2 3/16" SQUARE KEY 7 400126 2 WEIGHT BAR 30 100270 1 PULLEY, CLUTCH CABLE SUPPORT 8 300080 2 1/2" WHEEL PIVOT PIN 31 500042 4 3/8" FLAT WASHER 9 300081 2 WEIGHT STOP 32 500179 1 V-BELT GUIDE BOLT (3/8" x 2-3/4") 10 500133 2 5/16" x 1" BOLT 33 300107 2 PULLEY MOUNTING BRACKET 11 500115 2 5/16" LOCK WASHER 34 100256 2 DECAL, "CA-18" 12 500101 2 5/16" NUT 35 500218 1 1/4" x 1-1/4" BOLT 13 600027 1 KEYED SHAFT 36 500139 1 1/4" LOCK NUT 14 100031 2 REAR TIRE, 8" 37 500154 1 3/8" x 2-3/4" BOLT 15 500053 4 5/8" FLAT WASHER 38 100055 1 DECAL, "SERIAL NUMBER" (NOT SHOWN) 16 500016 2 5/32" x 1-1/4" COTTER PIN 39 100069 1 DECAL, "DANGER" (NOT SHOWN) 17 400142 1 ARM, L.H. REAR AXLE SUPPORT 40 100073 1 LUBRICATION TAG (NOT SHOWN) 18 500071 2 1/4" x 5/8" FINE BOLT 41 100074 2 DECAL, "CLASSEN" (NOT SHOWN) 19 500137 6 1/4" LOCK WASHER 42 100096 1 DECAL, "ALL GUARDS" (NOT SHOWN) 20 500164 4 1/4" FENDER WASHER 43 300079 2 WHEEL PIVOT FLAT 21 500029 4 1/4" x 3/4" BOLT 44 500083 2 5/16" FLAT WASHER 22 500136 4 1/4" NUT 45 500078 2 "E" RING 23 100250 2 SPRING 6 Parts Power Train and Tine Rotor Assembly CA-18 COMPACT AERATOR KEY 1 1 2 3 4 5 6 7 8 9 10 11 500159 1 3/8" x 2-3/4" BOLT KEY PART NO. SHEET DESCRIPTION 12 400136 1 ARM, BELT TIGHTENER 30 500174 1 1/2" x 1-3/4" BOLT 13 500130 1 3/8" LOCK WASHER 31 500006 1 1/2" LOCK WASHER 14 500129 1 3/8" NUT 32 500106 1 1/2" NUT 15 500091 1 3/8" x 2" BOLT 33 500175 1 3/8" x 3-3/4" BOLT 16 100010 1 IDLER PULLEY 34 100246 2 TIRE & WHEEL, 10 x 3W 17 500042 3 3/8" FLAT WASHER 35 500172 2 ROLL PIN, 1/4" x 1-1/2" 18 700023 1 TINE SHAFT ASSEMBLY 36 600026 1 AXLE, FRONT DRIVE 19 100032 24 TINE 37 100249 1 SPROCKET, #40 B21 x 3/4" 20 500169 50 5/16" LOCK NUT 38 100038 1 PULLEY w/ 3/4" HUB, 3/4" x 3" 21 100253 1 SPROCKET, #40 B27 x 1" 39 500041 2 3/8" LOCK NUT 22 500003 1 1/4" x 7/8" HALF MOON KEY 40 500173 1 KEY, 3/16" x 7/8" HALF MOON 23 300073 1 SPACER, TINE SHAFT 41 500140 12 5/16" x 3/4" BOLT 24 100248 2 BEARING, PLATED FLANGE w/ COLLAR, 1" 2 BOLT 42 100263 1 DEFLECTOR, HONDA ENG. (NOT SHOWN) 25 100254 1 CHAIN, #40 x 109 PITCH 43 100264 1 DEFLECTOR, B&S ENG. (NOT SHOWN) 26 100025 1 CONNECTING LINK 44 100265 2 SCREWS, DEFLECTOR 27 400137 1 ARM, CHAIN TIGHTENER 45 500034 1 1/2" FLAT WASHER 28 500114 1 5/16" x 2-1/4" TAP BOLT 46 500083 2 5/16" FLAT WASHER 29 100043 1 IDLER SPROCKET 47 500073 1 5/16" x 1-1/4" BOLT Parts Handle and Control CA-18 COMPACT AERATOR QTY/PER QTY/PER KEY PART NO. SHEET DESCRIPTION KEY PART NO. SHEET DESCRIPTION 1 400128 1 MAIN HANDLE 11 400130 1 ARM, L.H. LINKAGE 2 400017 1 LOWERING HANDLE 12 500091 4 3/8" x 2" BOLT 3 400180 1 CONTROL HANDLE 13 400133 1 LH LINKAGE PIVOT 4 100007 2 RUBBER GRIP 14 200035 1 CLUTCH CABLE 5 500134 9 3/8" x 1-1/4" BOLT 15 100034 1 SPRING...
Эта инструкция также подходит к моделям:Газонокосилки - 48-RT (2.29 mb)
Газонокосилки - 60-RT (2.29 mb)
Газонокосилки - 72-RT (2.29 mb)
Газонокосилки - CA-18 (2.29 mb)