Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the shaft. 1. Place the metal shield under the gearbox, and align the screw holes. _ Gearbox Shiek \ 2. Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. Tighten evenly and securely with the hex wrench provided. INSTALLATION OF THE METAL BLADE WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving. _WARNING: Do not use any blades, or fastening hardware other than the washers and nuts shown in the fol lowing illustrations. These parts must be provided by Sears and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others. 8 NOTE:Thedustcupandretaining washeronthegearbox arelocatedshaft andnotinthepartsbag.Allotherfas tenersmentionedas inthefollowing semblystepsareinthepartsbag. 1. Removewasher theretainingfrom thethreadedofthegearbox. shaft Leavethedustcupontheshaft. 2. Installthebladeandtheretaining washeroverthethreaded shaft. 3. Makesuretheraisedpartoftheretainingisfacing washerthegearbox andtheraisedareafitsintothehole inthecenter oftheblade. 4. Slidethebladewasher andretaining ontotheshaftofthegearbox. 5. Placethecuppedonto washerthe shaft.Makethecupped sureside ofthewashertheblade. istoward 6. Installthebladenutbythreading NOTE: Make sure all parts are in place as illustrated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer. Align hole in dust cup with hole in side of gearbox by rotating the blade. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while tightening the blade nut. Screwdriver _ 7. 8. ontotheshaftcounterclockwise. Gearbox Shield Dust Cup Retaining pE_lt_,_.. Washer _ Cupped Washer _ Nut 9. Tighten blade nut firmly with a wrench while holding screwdriver in position. 10. Remove the screwdriver. 11. Turn blade by hand. If the blade binds against the shield, or appears to be uneven, the blade is not centered, and you must reinstall. NOTE: To remove blade, insert screwdriver into aligned holes. Unthread the nut and remove parts. Be sure to store parts and instructions for future use. de KNOWBRUSHCUTTER YOURATTACHMENT READ THiS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR BRUSHCUTI-ER ATTAOHMENT Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Hanger j immer Shield _ B,adeBhied HeoB'ade B,ade Bh% BLADE The BLADE is designed for cutting grass, weeds, and brush up to 1/2 inch (1 cm) in diameter. TRIMMER HEAD The TRIMMER HEAD holds cutting line and is designed for cutting grass and light weeds. OPERATING THE COUPLER Your powerhead is equipped with a coupler which enables optional attachments to be installed. The optional attachments are: Edger ............... 71-79240 Cultivator ............ 71-79241 Blower .............. 71-79242 Pruner .............. 71-79245 _. WARNING: Always disconnect powerhead spark plug before removing or installing attachments. REMOVING BRUSHCUTTER ATTACHMENT (OR OTHER OPTIONAL ATTACHMENTS) CAUTION: When removing or installing attachments, place the powerhead and attachment on a flat surface for stability. 1= Loosen the coupler by turning the knob counterclockwise. BLADE SHIELD The BLADE SHIELD provides protection from the spinning blade. TRIMMER SHIELD The TRIMMER SHIELD provides protection from the spinning trimmer head. Upper Shaft Coupler LOOSEN Attachment TIGHTEiX Knob Press and hold the locking/release button. Locking/Release Button ""-,.,_ _---._ Attachment 3, While securely holding the upper shaft, pull the attachment straight out of the coupler. 10 INSTALLINGATTACH OPTIONAL MENT 1. Remove the shaft cap from the attachment (if present) and discard. 2. Position locking/release button of attachment into guide recess of upper shaft coupler. 3. Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4. Before using the unit, tighten the knob securely by turning clockwise. Coupler Primary HoleGuide Recess Upper Locking/ Attachment Shaft Release Button ,_ WARNING: Make sure the lock ing/release button is locked in the primary hole and the knob is securely tightened before operating the unit. Us ing the wrong hole could lead to serious injury or damage to the unit. Secondary Hoie Locking/Release Button in Primary HoIe INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use. To install hanger on attachment: 1. Remove the shaft cap from the attachment (if present) and discard. 2. Press and hold the locking/release button. 3. Push hanger onto the attachmen...
Эта инструкция также подходит к моделям:Газонокосилки - 358.792443 (1.28 mb)