Оценок - , средний балл:
(
)
)
Производитель: Honda Power Equipment
Размер: 472.87 kb
Название файла: cef15ca3-f436-2ac4-5dd9-4d168599aa1b.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
4. Si equipe de ressorts. lever I'instrument et les accrocher. DEVERROUILLE VERROUILLE PLACE ON MALE QUICK HITCH (CANADA ONLY ) d ro AVOID SERIOUS PERSONAL INJURY WHEN ATTACHIN6 OR OETACHIWG IMPLEMENT POUR EVITER LES BLESSURES GRAVES: PLACE ON WALE QUICK HITCH LOCATE0 ON MALE QUICK HITCH (CANADA 'ONLY ) (US & CANADA ) -IMPORTANT:---------Before beginning assembly of this subframe, make sure tractor is on a level surface, parking brake is set and that engine is turned off, with key removed. su~ERAME-PREP_ARAILoN a) Loosely attach rear hitch plate (fig.1, item 1) to bottom of subframe channel (fig.1, item 2). Use a 1/2" x 1 1/4" bolt (fig.1, item 31, flatwasher, lockwasher and nut, and a 1/2" x 5" bolt, long tube spacer (fig. 1, item 101, lockwasher and nut (fig.1, item 4). Do not tighten yet. b) Loosely attach subframe flatbars (fig.1, item 5) and the lift support brackets (fig.1, item 6) to the sides of channel (fig.1, item 2). Use four 1/2" x 1 1/2" bolts (fig.1, item 71, lockwashers and nuts. Do not tighten yet. c) Loosely attach the support plate (fig.1, item 8) inside the subframe flatbars (fig.1, item 5). Use four 318" x 1 1/4" bolts (fig.1, item 91, lockwashers and nuts. Do not tighten yet. LIELMSCHfl!!ISM a) Insert two 3/8" x 2 1/4" bolts (fig.2, item 1) through the smaller holes in the lift lever (fig.2, item 21, and secure them with a 3/8" uni-torque (stover) self-locking nuts.DC1 NOT EMD THE LEVER. b) Attach push arm (fig.2, item 3) to the lift lever (fig.2, item 2) with a 17/32" x 2 1/4" pin (fig.2, item 4) as shown. BE SURE TO USE THE CMiRECT HOLE. Use a 5/32" x 1" cotter pin to secure the pin (fig.2, item 4). OM 0149 FIGURE 1 F IGURE 2 Thread the adjustment fork (fig.2, item 5) into the end of the push arm (fig.2, item 3). Adjust the overall length of push arm assembly to 32 13/16". Place an 11/16" f latwasher and a bent retainer plate (fig.2, item 6) on the 5/8" x 4" bolt (fig.2, item 7). Insert the bolt into the lever as shown. Place another bent retainer plate and flatwasher on the bolt, and secure it loosely with a lockwasher and nut. Install a flange bearing (fig.3, item 1) into each lift support bracket (fig.3, item 2) from the inside. Insert the lift arm (fig.3, item 3) through the bearing in the right hand lift support bracket. Put a tube spacer (fig.3, item 4) on the arm, and then insert the arm through the lift lever (under the 5/8" bo1 t) . Insert the arm through another tube spacer, and then through the left hand lift support bracket bearing. The end of the arm should protrude 2 1/4" beyond the bearing. Position the subframe channel (fig.1, item 2) in line with subframe flatbars (fig. 1, item 5) and securely tighten bolts (fig.1, item 7 and 9). Rotate the lift arm (fig.4, item 3) so that its handle is parallel to the ground, and block in that position. Set the lift lever (fig.4, item 2) so that the 5/8" x 4" bolt(fig.4, item 4) is perpendicular to the ground, and then tighten the bolt to 50 lbs. ft. Install 1" x 4 1/2" plastic handle (fig.4, item 3) on lift arm (fig.4, item 1). FIGURE 3 a) Loosely attach the front support brackets (fig.5, item 1) to the tractor frame. For each bracket, use one lOmm x 1.25 x 25mm bolt (fig.5, item 2) with lockwasher, and two 10mm x 1.25 x 30mm bolts (fig.5, item. 3) with lockwashers for each bracket. Do not tighten yet. 6) Loosely attach the attaching plates (fig.5 9 item 4) to the front support brackets (fig.5, item 1). Use three 3/8" x 1" bolts (fig.5, item 5) with lockwashers for each plates. Do not tighten yet. C) Loosely install the reinforcement plate (fig.5, item 6) between the two attaching plates (fig.5, item 4). Use two 5/16" x . I FIGURE 5 314" bolts (fig.5, item 71, lockwashers and nuts IN THE FRONT HOLES MY. Install the bolts heads and lockwashers from the inside with the nut on the outside as shown. Do not tighten yet. W_A_RQPJg: To avoid injury, park the tractor on a level surface, turn off ,the engine, remove the key and set the parking brake. a Install male hitch (fig.6, item 1) in the pivot bracket (fig.6, item 2).Use four 7/16" x 1 1/4" bolts (fig.6, item 31, FIGURE 6 lockwashers and nuts. Install the bolts from the inside as shown, and tighten them securely. b) Position the subframe assembly under the tractor. Insert the rear of the assembly between the wheels on the right hand side of the tractor, and then pull itforward. OM 0149 c) Loosely attach front of subframe flatbars (fig.7, item 1) to the outside attaching plates. Use two 1/2" x 1 1/2" bolts (fig.7, item 31, lockwashers and nuts. Install the bolts from the inside as shown. Do not tighten yet. dl Attach the subframe's rear hitch plate (fig.1, item 1) to the tractor's rear draw plate with the 1/2" x 5" bolt (fig. 1, item 4). e) Securely tighten the 5/16 x 1/4" bolts (fig.5, item 7). Refer to the torque specification table on page 11. f) Slide the male hitch assembly (fig.8, item 1) between the attaching plates (fig.7, item 2). Align the hard bushing holes and attach the hit...