Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death. BOLT TORQUE Mounting procedures for mowers will require a significant amount of bolt nut and washer installation. Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness. Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart. Bolt tightness should be completed with and checked with a suitable torque wrench. Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual. Loose bolts on a frame or in a casting may be a result of: . . Vibration from the mower due to imbalance of the mower blades . . Pulled threads due to over tightening . . Distortion of the hole due to under tightening during installation Bolts broken or sheared in the mounting structure or tractor may be the result of: . . Improper alignment of the Mounting Plate or Structure such that it is not sitting flat on the mating surface . . Distortion of the bolt due to over-tightening . . Under tightening of the bolts Check the bolt torque during installation and prior to delivery with a suitable torque wrench. PARTS SECTION Parts Section – 1 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas 78155 830-379-1480 Parts Section – 2 ©2011 Alamo Group Inc. TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manuals thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER 1. Provide a Roll-Over-Protective Structure that meets the requirements of this standard. 2. Provide seat belts that meet the requirements of this paragraph of this standard and SAE J4C. 3. Ensure that each employee uses such seat belt while the tractor is moving. 4. Ensure that each employee tightens the seat belt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seat belt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going, especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly, no jerky turns, starts, or stops. 8. Hitch only to the draw bar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens. ALAMO INDUSTRIAL Limited Warranty 1. Limited Warranties 1.01. Alamo industrial warrants for one year from the purchase date to the original non-...