Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
If the temperature does not return to normal or the coolant level warning lamp is ON, shut down the tractor immediately. CAUTION: KEEP THE CAB FLOOR AREA FREE FROM DEBRIS OR OBJECTS WHICH MAY OBSTRUCT THE OPERATION OF THE BRAKE PEDAL. KEEP THE PEDAL CLEAN AND DRY TO PREVENT YOUR FOOT FROM SLIPPING OFF THE PEDAL. DANGER: NEVER LEAVE THE OPERATOR’S SEAT WITHOUT FIRST BRINGING THE TRACTOR TO A COMPLETE STOP USING THE FOOT BRAKE, AND THEN ENGAGING THE PARKING BRAKE. DANGER: NEVER OPERATE THE TRACTOR IF THE FOOT OR PARKING BRAKE DOES NOT FUNCTION PROPERLY. DANGER: NEVER RELY SOLELY ON THE TRANSMISSION TO HOLD THE TRACTOR STATIONARY WHEN PARKED, ALWAYS ENGAGE THE PARKING BRAKE. 435/485/535 Section 3 - Operation Transmission Operation Transmission Operation Synchromesh Transmission Operation The Synchromesh transmission has three forward ranges and one reverse range Within each range, including reverse, there are four synchronized speeds The synchronized speeds allow for easier shifting within each range This combination allows for twelve forward speeds and four reverse speeds All shifting is done manually, in conjunction with the clutch The transmission incorporates a shaft brake, which is designed to stop transmission rotation when shifting between ranges This is activated when the range lever is in neutral and the clutch pedal is fully depressed IMPORTANT: Engage the clutch at a low throttle setting and as light a draft load as possible to extend clutch and synchronizer life. Do not engage the clutch when the throttle is set higher than 1700 RPM while under load. Raise the implement whenever possible during shifting. Use the decelerator pedal to bring the engine speed down when shifting or engaging the clutch All gears in the transmission are constantly in mesh When a range is selected, shift collars splined to the shafts are being engaged with the range gears The tractor must be at full stop in order to shift between ranges. The transmission bearings and gears are pressure lubricated The lubrication circuit consists of a gear pump located on and driven by the transmission, an oil cooler located in front of the engine radiator, a filter located inside the frame at the front of the tractor, and the oil distribution manifold on the transmission The transmission case acts as a reservoir Should the transmission oil pressure warning lamp come on, (page 3-29) immediately shut down the tractor and contact your Buhler Versatile dealer to investigate the cause of lubrication failure CAUTION: KEEP THE CAB FLOOR AREA FREE FROM DEBRIS OR OBJECTS WHICH MAY OBSTRUCT THE OPERATION OF THE CLUTCH PEDAL. KEEP THE PEDAL CLEAN AND DRY TO PREVENT YOUR FOOT FROM SLIPPING OFF THE PEDAL, CAUSING ABRUPT ENGAGEMENT. Range Shifting Be sure the engine speed is below 700 RPM Whenever possible, reduce engine speed to idle 2 Depress the clutch fully and bring the tractor to a complete stop Place the range shift lever ( ) in neutral Wait three to four seconds to allow the transmission to slow down to a near stopped condition before selecting the desired range Shift pattern decals are located behind the shift lever indicating range position 3 If you are not able to move to the desired position, turn the steering wheel to the left or right to allow gears to mesh 4 Slowly release the clutch pedal to achieve a smooth start 5 Reset the engine speed to operating range The range shift decal located in front of the range shift lever positions for high (H), medium (M), low (L), or reverse (R) range F3-72(SET)OFFCRUISE1324NLHMRN2 1 435/485/535 Section 3 - Operation Transmission Operation Gear Shifting within a Range IMPORTANT: It is recommended that shifting gears with the tractor in motion be limited to light draft or rolling loads and only within a set range. Do not attempt to shift between ranges without first coming to a complete stop. Depress the clutch pedal fully 2 Move the gearshift lever (2) to the required gear Shift patterns are located in front of the shift levers indicating gear position NOTE: It is not necessary to reduce engine speed for shifts within a range, but is recommended to increase the life of shift components. 3 Release the clutch pedal slowly to insure a smooth transmission engagement NOTE: While it is possible to shift with the tractor in motion within a range, under heavy loads the tractor will probably come to an abrupt stop before the shift is complete. For your safety, it is recommended that the operator throttle down, raise any implements, and stop before attempting any shifts. Forward/Reverse Shifting Shuttle shifting should not be attempted between the forward and reverse ranges while the tractor is still moving Harsh transmission engagement will occur as well as damage to the range shift mechanisms in the transmission Bring the tractor to a complete stop before shifting the range lever 2 Select the range desired 3 Release the clutch pedal slowly to achieve a smooth start LH N MR F3-70 Range shift pattern 13 N 24 F3-71...
Эта инструкция также подходит к моделям:Газонокосилки - 435 (9.35 mb)
Газонокосилки - 535 (9.35 mb)