Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
For ROMMON software upgrade details, refer to The ATA Flash PC card is supported on Catalyst 6500 series switches running Cisco IOS Release 12.1(8a)EX or later releases on both the supervisor engine and the Multilayer Switch Feature Card (MSFC). The ATA Flash PC card is supported on Catalyst 6500 series switches running Catalyst software release 7.5(1) or later releases on the supervisor engine and Cisco IOS on the MSFC. Note The 64-MB linear Flash PC card (MEM-C6K-FLC64M) is supported only on Supervisor Engine 1 and requires ROMMON software release 5.3(1) or later releases. The 64-MB linear Flash PC card is supported on Catalyst 6500 series switches running Cisco IOS Release 12.1(13)E4 or later releases on both the supervisor engine and the MSFC. The 64-MB linear Flash PC card is supported on Catalyst 6500 series switches running Catalyst software release 7.5(1) or later releases on the supervisor engine and Cisco IOS software on the MSFC. Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA © 1999–2005 Cisco Systems, Inc. All rights reserved. Contents Contents This installation note contains the following sections: • Supervisor Engine Flash PC Cards, page 2 • Preventing Electrostatic Discharge Damage, page 3 • Installing and Removing a Flash PC Card, page 3 • Using Flash PC Cards, page 6 • Additional Documentation, page 8 • Obtaining Documentation, page 8 • Documentation Feedback, page 9 • Cisco Product Security Overview, page 9 • Obtaining Technical Assistance, page 10 • Obtaining Additional Publications and Information, page 12 Supervisor Engine Flash PC Cards The supervisor engine Flash PC cards conform with the PCMCIA format. These models are available: • 16-MB MEM-C6K-FLC16M • 24-MB MEM-C6K-FLC24M • 64-MB MEM-C6K-FLC64M • MEM-C6K-ATA-1-64M Note The 16-MB MEM-C6K-FLC16M and 24-MB MEM-C6K-FLC24M linear Flash PC cards are formatted for the Catalyst 6500 series supervisor engines and are ready to use. The MEM-C6K-ATA-1-64M and 64-MB MEM-C6K-FLC64M Flash PC cards are not formatted. You must format these cards (See Table 1 on page 7 Commands for Using and Managing Flash DevicesTable 1for a description of the format command.) When you enter the dir disk0: or dir slot0: commands, an unformatted Flash PC card returns a “bad device block info” or “invalid magic number” error message. Note Supervisor Engine 1 and Supervisor Engine 2 do not support the same Flash PC card format. To use a Flash PC card with Supervisor Engine 2, you must format the card with Supervisor Engine 2. To use a Flash PC card with Supervisor Engine 1, you must format the card with Supervisor Engine 1. You can use Flash PC cards to store and boot software images, or they can be used as servers to store software images for other systems. You can configure each supervisor engine with one Flash PC card in slot 0. Figure 1 shows the front panel of a supervisor engine with the single PCMCIA slot, slot 0. 2 Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note 78-6507-06 Preventing Electrostatic Discharge Damage Figure1 Supervisor Engine Flash PC Card Slot 16057SUPERVISOR I WS-X6K-SUP1 STATUSSYSTEMACTIVEPWR MGMTRESET CONSOLE Switch Load 100% 1% CONSOLE PORT MODE PCMCIA EJECT PORT 1 LINK PORT 2 LINK PCMCIA LED LINK LEDs Switch load display Status LEDs RESET button CONSOLE port CONSOLE PORT MODE switch PCMCIA slot 1000BASE-X GBIC Uplink Ports For information about using the PCMCIA Flash PC cards, see the “Using Flash PC Cards” section on page 6. Preventing Electrostatic Discharge Damage Follow these guidelines to prevent electrostatic discharge (ESD) damage: • Always use an ESD wrist or ankle strap, and ensure that it makes good skin contact. • Connect the equipment end of the strap to the ESD connector on the switch. • Place a removed Flash PC card on an antistatic surface or in a static shielding bag. If the card will be returned to the factory, immediately place it in a static shielding bag. • Avoid contact between the card and clothing. The wrist strap only protects the card from ESD voltages on the body; ESD voltages on clothing can still cause damage. Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be between 1 and 10 megohms. Installing and Removing a Flash PC Card Before you install a Flash PC card, verify that the card’s write-protect switch is off. When the card is oriented with the printing side up and the edge connector end away from you, the write-protect switch is located on the front edge of the card, as shown in Figure 2. Note Not all Flash PC cards have the write-protect switch. Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note 78-6507-06 3 Installing and Removing a Flash PC Card Figure2 Locating the Flash PC Card Write Protection Switch Flash PC card Flash PC card write protection Flash PC card shown with writ...
Эта инструкция также подходит к моделям:Газонокосилки - CATALYST MEM-C6K-FLC16M (180.54 kb)
Газонокосилки - CATALYST MEM-C6K-FLC24M (180.54 kb)
Газонокосилки - CATALYST MEM-C6K-FLC64M (180.54 kb)