Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Spray Gun Assembly 7. Axle 8. Hitch Arms (2) 9. Hitch Brackets (2) 10. Wheels (2) 1. Lid 2. Tank 3. Return/Bypass Hose (may be assembled to tank) 4. Boom Assembly 5. Boom Mount Bracket 13610947528 ENGLISH SHOWN FULL SIZE OP204060801000NOT SHOWN FULL SIZEQRTUSNAHJKLBCDGFEIM HARDWARE PACKAGE - FULL SIZE KEY QTY. DESCRIPTION A 8 Hex Bolt, 5/16" x 2" B 2 Hex Bolt, 5/16" x 1-1/4" C 2 Carriage Bolt, 5/16" x 1-1/4" D 2 Screw, #10 x 3/8" E 4 SEMS Nut, 5/16" F 10 Nylock Nut, 5/16" G 2 Flat Washer, 5/16" H 4 Flat Washer, 3/4" I 2 Lock Washer, #10 J 2 Washer, 5/16" Tooth Lock K 1 Hitch Pin KEY QTY. DESCRIPTION L 1 Hair Cotter Pin M 2 Cotter Pin N 2 Knob O 1 Spray Gun Clip, Small P 1 Spray Gun Clip, Large Q 1 Pressure Gauge R 2 Spacer S 1 Coiled Hose Clamp T 2 Gasket, 3/4" Garden Hose U 2 Axle Clamp, 3/4" ENGLISH ASSEMBLY INSTRUCTIONS 6. Assemble a hitch arm to the inside of a frame tube underneath the tank. Use two 5/16" x 2" hex bolts and 5/16" nylock nuts as shown in figure 3. Do not tighten yet. Repeat for other side. TOOLS REQUIRED FOR ASSEMBLY (2) 1/2" Wrenches (1) Screwdriver (1) Pliers 5/16" x 2" HEX BOLT5/16" NYLOCK NUTHITCH ARM 1. Remove all items from carton and lay out as shown on pages 2 and 3. 2. Assemble the axle clamps and four 5/16" SEMS nuts to the factory installed bolts in the frame tubes. Do not tighten yet. See figure 1. FACTORYINSTALLEDBOLTAXLECLAMP5/16" SEMS NUT FIGURE 3 7. Fasten the ends of the hitch arms together using two 5/16" x 1-1/4" hex bolts and 5/16" nylock nuts. Do not tighten yet. See figure 4. 8. Assemble the hitch brackets to the hitch arms using two 5/16" x 2" hex bolts and 5/16" nylock nuts. Position each bolt behind a cross bolt in the hitch arms. Do not tighten yet. See figure 4. 5/16" x 2" HEX BOLT5/16" NYLOCK NUT5/16" x 1-1/4" HEX BOLT5/16" NYLOCK NUT FIGURE 1 3. Slide the axle through the two axle clamps. See figure 2. 4. Assemble a spacer, a 3/4" washer, a wheel (valve stem facing out) and another 3/4" washer onto the axle. Assemble a cotter pin through the end of the axle. Repeat on other end. See figure 2. 5. Tighten the four nuts which fasten the axle clamps to the frame tubes. Refer back to figure 1. 3/4" WASHERSPACER1/8" x 1-1/2" COTTER PIN FIGURE 4 9. Tighten all bolts starting with the bolts in figure 3, then the bolts in figure 4. FIGURE 2 ENGLISH 10. Assemble the boom mount bracket to the rear of the frame tubes using two 5/16" x 2" hex bolts and 5/16" nylock nuts. See figure 5. 12. Assemble the large and small spray gun clips to the side of the tank using two #10 x 3/8" screws and #10 lock washers. See figure 7. 5/16" NYLOCK NUT5/16" x 2" HEX BOLT SPRAY GUNCLIP (LARGE)SPRAY GUNCLIP (SMALL) #10 x 3/8" SCREW#10 LOCKWASHER FIGURE 5 REAR VIEW FIGURE 7 11. Assemble the boom bars to the boom mount bracket using two 5/16" x 1-1/4" carriage bolts, tooth lock washers (between the bar and bracket), 5/16" flat washers and knobs. The boom connecting hose should extend upward. See figure 6. NOTE: Make sure the nozzles are adjusted so that the openings face straight down when the boom bar is in the horizontal operating position. CARRIAGE BOLT5/16" x 1-1/4" KNOB5/16" FLATWASHERWASHER(TOOTH LOCK) BOOM BARBOOM CONNECTING HOSE FIGURE 6 ENGLISH 17. Attach the sprayer to the tractor hitch and connect the wiring to the tractor battery. The red wire must be connected to the positive post on the battery or to the "HOT" connection on a tractor switch or ammeter. The brown wire may be grounded or connected to the negative battery post. See figures 9 and 10. 13. Insert a garden hose gasket into the swivel nut on the bypass/return hose. Screw the nut onto the upper outlet of the "Y" valve fitting. Place the other end of the hose down through the hole at the rear of the tank. See figure 8. 14. Insert a garden hose gasket into the swivel nut on the boom connecting hose. Screw the nut onto the lower outlet of the "Y" valve fitting. See figure 8. 15. Slide the coiled hose clamp onto the spray gun hose. Push the hose onto the hose adapter on the side of the "T" fitting as shown in figure 8. Tighten the clamp around the hose and the adapter. Snap the spray gun into the clips on the side of the tank. 16. Carefully screw the pressure gauge into the top of the "T" fitting. See figure 8. IMPORTANT: This sprayer should be connected to 12 volt batteries only! BROWNREDQUICK COUPLERBATTERY+REDBROWNIN LINE SWITCH FIGURE 9 BOOM CONNECTING HOSESPRAYGUNHOSEPRESSUREGAUGEBYPASS/RETURN HOSEGARDENHOSEGASKETCOILED HOSECLAMP DANGER! Never allow negative pin on plug to come in contact with positive "hot" post on battery. Fire or explosion may result! PLUGNEGATIVE PIN12 VOLT TRACTOR BATTERYPOSITIVE"HOT" POST+ NEGATIVEPOST FIGURE 8 FIGURE 10 ENGLISH OPERATION USING THE SPRAYER 1. Determine the application rate (gallons per 1,000 sq. feet or gallons per acre) based on the chemical manufacturers recommendations. Use this rate to help select the pressure setting and tractor speed in the following instructions. 2. Determ...