Оценок - 5, средний балл: 3.4
(
)
)
|
Фрагмент инструкции
8) 8 1. Raise mower to highest position to allow access to blade. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth. 2. Remove blade bolt by turning coun ter clock wise. 3. Install new blade with stamped "GRASS SIDE" facing downward. IMPORTANT: To ensure proper as sem bly, center hole in blade must align with star on mandrel assembly. 4. Install and tighten blade bolt securely (45-55 Ft. Lbs.). IMPORTANT: Special blade bolt is heat treated. BLADE BLADE BOLT (SPECIAL) CENTER HOLE STAR MANDREL ASSEMBLY Fig. 8 LEVEL MOWER DECK Ensure deck is properly leveled for best mower per for mance. See your riding mower owner's manual for instructions. 10 COUNTERWEIGHT (See Fig. 9) 1. Lower mower to lowest position to allow access to front axle. 2. Turn steering wheel all the way to the right, for access to left side of axle 3. With extension and socket, insert bolt, lock washer, and washer through hole in axle. NOTE: Insert hardware from rear of axle. 4. Hold counterweight up to axle and start threading bolt. 5. Repeat steps 2-3 from right hand side. IMPORTANT: Torque bolts until tight. WASHER LOCKWASHER BOLT COUNTERWEIGHT Fig. 9 9 OPERATION TIPS FOR IMPROVED BAGGING OPE RATION: Follow the mower operation instructions in your riding mower owner's manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total time of operation may be greater than you will experience with regular use of your grass catcher. • Always run throttle at full speed when bagging. • Select a gear low enough to give good mower cutting performance, good quality cut and good bagging per- for man ce. NOTE: It may be necessary to overlap width of cut to suit your conditions. • If grass is extremely tall, it should be mowed twice. The first time relatively high, the second time to desired height. • Use left hand side of mower for trimming. • Plastic trash bags can be inserted inside grass catcher containers for ease of debris disposal. To remove the plastic trash bags when full: a. Disengage blades, shift into neutral, en ga ge the par king brake and stop the engine. b. Unlatch and raise cover. c. Remove one container at a time by grasping con tai ner handles and pulling toward the rear, off of the tube rails. d. With the container resting on the ground, close and secure the top of the plastic lawn bag. e. Tip the container on its side and slide the filled bag from the container. f. Install a new plastic lawn bag with the edges of the bag draped over upper lip of the container. g. Repeat for other containers. h. Reinstall containers making sure right con tai ner overlaps left container at center supports. j. Close cover and secure latches over center support tubes. • Avoid cutting wet grass or in the morning while the dew is still heavy. Grass clippings collected under these conditions tend to be sticky and adhere to the walls of the flow path causing clogging. • Your bagger is equipped with a full bagger indicator. Movement of the wheel increases as the bags fill. The wheel will be spinning fastest just before the bags fill completely. When the wheel stops, it indicates that the bags are full and the chutes have become clogged. NOTE: To help prevent clogging of chutes, check/empty bags when the wheel is spinning fast. Experience will teach you the best time to empty the bags. Care should be taken not to damage the parts and that the wheel spins freely at the beginning of each use. • If the grass catcher fails to pick up cut grass or leaves, it is an indication that clogging has occurred in the system or that the grass catcher containers are full. Usually this is indicated by the stopped movement of the full bagger indicator. a. Disengage blade, shift into neutral, en ga ge the par king brake and stop the engine. - Unlatch and raise cover. - Slide out containers and dispose of clip pings. - Replace containers, close cover, and latch. b. Unlatch chutes and check for clogging. - Remove all debris in chutes. - Reassemble and latch chutes c. Check to insure full bagger indicator has not become clogged. - The air passage hole must be clear of debris. Gently insert a small twig or wire into pas sage way to clear. CAUTION • Do not operate mower with grass catch er par tial ly installed. • Disengage blade and stop engine be fore leaving riding mower seat to empty con tain ers, un clog ging chutes, etc. • Close cover before starting. • Disengage mower when crossing drive ways or gravel surfaces and other areas where thrown objects could be a hazard. • Do not attempt to vacuum up cans or other potentially hazardous pro jec tiles. 10 CUSTOMER RESPONSIBILITIES GENERAL RECOMMENDATIONS Always observe safety rules when performing any mainte nance. • Before each use check for loose fasteners. • Clean unit thoroughly after each use. BLADE CARE For best results, mower blade must be kept...
Эта инструкция также подходит к моделям:Газонокосилки - 960 73 00-27 (984.58 kb)
Газонокосилки - 532 43 46-60 (984.58 kb)