Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Refer to figure 10. FIGURE 12 I BLADE PLANE ADJUSTMENT The cutting blade can be adjusted to eight positions from vertical to horizontal. To adjust, release tie adjustment lever on the pivot bracket and rotate ihe spindle housing. Place adjustment lever in nolch desired. See figure 13. When the blade is adjusted toward the horizontal position, the front wheels must also be adjusted. Remove the two hairpin cotters and slide the spacer and wheel to the right as shown in figure 14. Reinsert the hairpin cotters. NOTE If the wheels are not adjusted, the blade will hit the left front wheel, causing the belt to slip. HAIR PIN COTTERS FIGURE 14 Become familiar with all the controls and adjustments before operating the edger so you can adjust it easily to a variety of cutting and trimming conditions. While the engine is running, DO NOT ATTEMPT TO MAKE ANY ADJUSTMENTS except with the throttle control. OPERATION 1. Fill the crankcase with oil using a high quality detergent oil classified " For Service MS." Nothing should be added to the recommended oil. SUMMER- Use SAE 30. WINTER - (Below 40° F.) Use SAE 5W-20orSAE 10W. Place the engine level. Remove filler plug. FILL THE OIL SUMP TO POINT OF OVERFLOW. Pour slowly. See figure 15. 2. Fill the fuel tank with clean, fresh, lead-free, low-lead, or regular grade leaded gasoline. DO NOT MIX Ol L WITH GASOLINE. 3. Move the engagement handle (depth control) back as far as it will go and place in the last notch. See figure 12. 4. Set the throttle control in "START" position. 5. Pull the choke knob out. A warm engine may not require choking. 6. Grasp the starter handle and pull out the cord rapidly. Return it slowly to the engine. If the engine does not start after two pulls, move the throttle control to the "FAST" position. 7. After engine starts, push choke knob in gradually. To stop engine, move throttle control to "STOP" position. Disconnect spark plug wire and ground to prevent accidental starting while equipment is unattended. 8 A CAUTION Rotating cutting blade may throw objects causing personal injury. Always wear safety glasses or some other suitable eye protection at all times the engine is running. Keep area clear of bystanders and do not operate without guards in place. OPERATING THE EDGER 1. Set the adjustment lever (refer to figure 12) in the second notch at the top to edge vertically. See figure 16. 3. Move the front wheels all the way to the left when using the edger on a curb. See figure 18. FOR USE ON CURBS FIGURE 18 FLAT DRIVE t e> FIGURE 16 To operate the unit as a trimmer, move the adjustment lever and rotate the cutting blade 90°. See figure 19. Move the front wheels all the way to the right, as described in the Control section. A CAUTION Do not adjust the blade guard with the engine running. T-4- ! L ff [] J-iy£ 41 \ tSl, 2. Set the adjustment lever (refer to figure 13) in the first notch at the top for trenching. See figure 17. TRENCHING FIGURE 17 UP TO FENCE, FOUNDATIONS, ETC. FIGURE 19 LUBRICATION Wheels - The wheels are plastic and require no lubric-cation. Engine - Refer to engine manual for lubrication instructions. Cutting Head Bearings - The two ball bearings in the cutting head are lubricated and sealed at the factory and require no lubrication. Lubricate all other moving parts with engine oil. Shaft - Lubricate the two bearings and under the compression spring on the shaft with light oil at least once a season. See figure 20. 9 I MAINTENANCE A fSSSKSTi Disconnect the spark plug wire and ground against the engine before performing any adjustment, repairs or maintenance. BLADE REMOVAL Use a wrench on both sides of the blade when removing it for replacement. BELT REMOVAL 1. To remove the V-belt, remove the belt guard assembly at the engine pulley. Remove the hex nuts and lock washers. See figure 20. 2. Remove the belt guard at the spindle assembly by removing two hex bolts, lock washers and hex nuts. See figure 21. 3. Remove the old belt, and reassemble with a nsw belt, part number 754-0142. HEX NUTS FIGURE 20 ENGINE OIL Check oil level before starting engine and after every 5 hours of operation. Add oil as necessary to keep level full to point of overflowing. Before removing plug, clean area around plug to prevent dirt from entering oil fill opening. Refer to figure 15. Change oil after first 5 hours of operation. Thereafter, change every 25 hours. Change oil while engine is warm. Oil may be drained thru oil drain plug. Crankcase capacity - 1-1/4 pints. Refer to engine manual for complete instructions for care and maintenance of engine. OFF-SEASON STORAGE The following steps should be taken to prepare unit for storage. 1. Clean and lubricate unit thoroughly. 2. Refer to engine manual for correct engine storage instructions. 3. Coat unit's cutting blade with chassis grease to prevent rusting. 4. Store unit in a dry, clean area. ¡H^N0TE When storing any type of power equipm...
Эта инструкция также подходит к моделям:Газонокосилки - 247-604-000 (1.38 mb)