Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Maximum rating : 1.00mm2 size cable, 10 amps 250 volts AC. • THE VENTURER 320 IS SUPPLIED WITH CABLE WIRED DIRECTLY INTO THE PRODUCT. 1. Flymo Mains Cables and Extension Cables are available from your local Electrolux Outdoor Products Approved Service Centre. 2. Do not wire an extension cable directly to your product yourself. Please contact your local Electrolux Outdoor Products Approved Service Centre for further information on the connectors and kits available. 3. Only use extension cables specifically designed for outdoor use. CONNECTORS IMPORTANT • Flymo connectors are suitable for use with 2 core cable only. Under no circumstances should these connectors be used for earthed products. • All Flymo connectors and cables are of splashproof construction. They are not waterproof and must not be left outside permanently nor should they be submerged or immersed in water. Do not let cable lay or trail through pools of water or splashed with water from hose pipes. MAINS PLUG REPLACEMENT IMPORTANT • If the plug supplied is cut off it should be destroyed. There is an electric shock hazard if a cut off plug is inserted into a 13 amp socket. 1. No earth required. Flymo products are double insulated to EN60335 and under no circumstances should an earth be connected to any part of the product. 2. Ensure the mains voltage suits your product 3. IMPORTANT! The wires in the mains lead are coloured in accordance with the following code: BLUE - NEUTRAL BROWN - LIVE The wire which is coloured BLUE must be connected to the Terminal which is marked with the letter 'N' or coloured BLACK. The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter 'L' or coloured RED. 4. It is important that the outer sheath is clamped correctly into the 3-pin plug. 5. If in doubt consult your local Service Repairer or qualified electrician before the machine is used. 6. A 13 Amp fuse must be fitted to the Mains Plug. 7. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. If your product is hard wired i.e. non-detachable mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor Products Approved Service Centres which can be found in your local Yellow Pages. ensure the point of the screw stays inside the handle. B C D 1 Cutting Height Adjustment Wheels - Front Cutting Height Adjustment • Height of cut is adjusted by raising or lowering the front wheels and rear roller. • NOTE The wheels and the roller must be adjusted to the same position: HEIGHT OF CUT WHEEL ROLLER Low Hole 1 Position H Medium Hole 2 Position J High Hole 3 Position K • NOTE A medium height of cut is recommended for most lawns. 1. To remove the wheel assembly turn the wheel hub in an anti-clockwise direction.(E) 2. Select one of the 3 holes in the mounting plate and note it as the other wheel will need to be adjusted to the same position.(F) 3. Locate fixing bolt through hole in hub cap, wheel and selected hole in mounting plate.(F) 4. Turn the wheel hub in a clockwise direction until the wheel assembly is securely located to the deck.(E) 5. Using the same height adjustment position repeat the procedure for the other wheel. Roller and Rear Height Adjustment H - LOW J - MEDIUM K - HIGH 1. Select one of the 3 locations and note it as the other lever will need to be adjusted to the same position. (H, J or K) 2. Lift the lever out of location and rotate the roller to the desired position. (G) 3. Using the same height adjustment position repeat the procedure for the other lever. to remove turn anti-clockwise to fit turn clockwise E 1 2 3 F mounting plate holes wheel hub cap fixing bolt G H J K Grassbox Fitting Fully Assembled Grassbox to Lawnmower. See Fig L. 1. Lift safety flap. 2. Make sure the discharge chute is clean and free from debris. 3. Locate fully assembled grassbox onto 2 location points at the rear of the deck 4. Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. • IMPORTANT ! AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. • Removal is the reverse procedure. • For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox. Ensure the Safety Flap is fully closed. The design of the safety flap permits the cut grass to be discharged downward behind the machine. L M N R Starting and Stopping To Start your Lawnmower 1. Form loop in mains cable and push the loop through the slot. (M) 2. To secure, position loop over the hook and pull the cable back through the slot (N). 3. Connect plug to mains and switch on. 4. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting. The switchbox is provided with a lock-off button (P1) to prevent accidental starting. 5. Press and hold the lock-off button (P) on the switchbox, then squeeze one of the Start...