Войти:
Оценок - 3, средний балл: 3.3 ( )

Инструкция по эксплуатации Sony, модель DSC-P120

Производитель: Sony
Размер: 2.71 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


p Install the battery pack correctly (page 11). — Troubleshooting Symptom Cause Solution The battery remaining indicator is incorrect, or sufficient battery remaining indicator is displayed but the power runs out soon. • You have used the camera in an extremely hot or an extremely cold location. • A deviation has occurred in the remaining battery time. • The battery pack is discharged. • The battery pack is dead (page 118). p See page 118. p Fully discharge and then charge the battery pack so that the battery remaining indicator functions correctly (page 12). p Install a charged battery pack (page 11). p Replace the battery pack with a new one. The battery pack runs • You have used the camera in an extremely cold p See page 118. down too quickly. location. • The DC plug is dirty so the battery pack is not charged enough. • The battery pack is dead (page 118). p Clean the pins of the DC plug with a cotton swab, etc., and charge the battery pack (page 11). p Replace the battery pack with a new one. You cannot turn on the camera. • The battery pack is not installed correctly. • The AC Adaptor is disconnected. • The AC Adaptor has malfunctioned. • The battery pack is discharged. • The battery pack is dead (page 118). p Install the battery pack correctly (page 11). p Properly connect the AC Adaptor (page 14). p Consult your Sony dealer or local authorized Sony service facility. p Install a charged battery pack (page 11). p Replace the battery pack with a new one. The power turns off suddenly. • If you do not operate the camera for about three minutes while the power is on, the camera turns off automatically to prevent wearing down the battery pack (page 15). • The battery pack is discharged. p Turn on the camera again (page 15) or use the AC Adaptor (page 14). p Install a charged battery pack (page 11). Shooting still images/movies Symptom Cause Solution The LCD screen is not turned on even when the power is turned on. • The power was turned off with the LCD screen turned off the last time you used the camera. p Turn on the LCD screen (page 30). The subject is not visible on the LCD screen. • The mode dial is not set to , P, M, SCN or . p Set it to , P, M, SCN or (page 10). Symptom Cause Solution The LCD screen turns blue and the subject does not appear when recording movies. • The image size is set to [640(Fine)] while an A/V multi cable is connected to the multi connector. p Disconnect the A/V multi cable. p Set the image size to other than [640(Fine)]. The image is out of focus. • The subject is too close. • (Twilight mode), (Landscape mode) or (Fireworks mode) is selected for the Scene Selection function. • The focus preset function is selected. p Record in the close-ups (Macro) recording mode. Make sure to position the lens farther away from the subject than the shortest shooting distance when shooting (page 26). p Set it to other modes than (Twilight mode), (Landscape mode) or (Fireworks mode) (page 35). p Set to the auto focus mode (page 49). Zoom does not work. • You cannot change the zoom scale when shooting movies. — Precision digital zoom does not function. • [Digital Zoom] is set to [Smart] or [Off] in the SET UP settings. • This function cannot be used during shooting movies. Set [Digital Zoom] to [Precision] (pages 25, 45 and 113). — Smart zoom does not function. • [Digital Zoom] is set to [Precision]or [Off] in the SET UP settings. • The image size is set to [5M] or [3:2]. • You are shooting in Multi Burst mode. • This function cannot be used during shooting movies. p Set [Digital Zoom] to [Smart] (pages 25, 45 and 113). p Set image size to other settings except [5M] and [3:2] (pages 19 and 25). p The smart zoom cannot be used in Multi Burst mode (pages 25 and 59). — The image is too dark. • You are shooting a subject with a light source behind the subject. • The brightness of the LCD screen is too low. p Select the metering mode (page 55). p Adjust the exposure (pages 52, 53 and 109). p Adjust the brightness of the LCD backlight (page 114). The image is too bright. • You are shooting a spotlighted subject in a dark location such as on a stage. • The brightness of the LCD screen is too bright. p Adjust the exposure (pages 52, 53 and 109). p Adjust the brightness of the LCD backlight (page 114). The image is monochrome (black and white). • [PFX] (P. Effect) is set to [B&W]. p Set it to the other modes than [B&W] (page 60). Troubleshooting Symptom Cause Solution Vertical streaks appear when you are shooting a very bright subject. • The smear phenomenon is occurring. p This phenomenon is not a malfunction. Noise appears in the image when you view the LCD screen in a dark place. • The camera is functioning to increase the visibility of the LCD screen by temporarily brightening the image under conditions of low illumination. p There is no effect on the recorded image. Your camera cannot record images. •No “Memory Stick” has been inserted. • The capacity of the “Memory Stick” is full. • The write-protec...

Эта инструкция также подходит к моделям:
Фотоаппараты - DSC-P100 (2.71 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории