Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
S. A. only. A/M and M/A Modes • M/A: Autofocus can be over-ridden by rotating the lens focus ring. • A/M: As above, except that the focus ring must be rotated farther before the autofocus is over-ridden, preventing accidental changes to focus caused by unintended operation of the focus ring. z Slide the lens focus-mode switch to A/M or M/A. x Focus. If desired, autofocus can be over-ridden by rotating the lens focus ring while the shutter-release button is pressed halfway (or, if the camera is equipped with an AF-ON button, while the AF-ON button is pressed). To refocus using autofocus, press the shutterrelease button halfway or press the AF-ON button again. The Focus Limit Switch This switch determines the focus distance limits for autofocus. • FULL: Select this option for subjects that may be closer than 6 m (19.69 ft). • .–6 m: If your subject will always be at distance of at least 6 m (19.69 ft), select this option for faster focusing. ¦ Zoom and Depth of Field Before focusing, rotate the zoom ring to adjust the focal length and frame the photograph. If the camera off ers depth-of-fi eld preview (stop down), depth of fi eld can be previewed in the viewfi nder. Note: Focal length decreases as the focus distance shortens. Note that the focus distance indicator is intended only as a guide and may not accurately show the distance to the subject and may, due to depth of fi eld or other factors, not show . when the camera is focused on a distant object. To lock the zoom ring, rotate it to the 80 mm position and slide the zoom lock switch to LOCK. This prevents the lens extending under its own weight while the camera is being carried from place to place. ¦ Aperture Aperture is adjusted using camera controls. Zoom and Maximum Aperture Changes to zoom can alter the maximum aperture by up to 2.3 EV. The camera however automatically takes this into account when setting exposure, and no modifi cations to camera settings are required following adjustments to zoom. ¦ Built-in Flash Units When using the built-in fl ash on cameras equipped with a built-in fl ash unit, remove the lens hood to prevent vignetting (shadows created where the end of the lens obscures the built-in fl ash). ¦ Vibration Reduction (VR) Vibration reduction (VR) reduces blur caused by camera shake, allowing shutter speeds up to 4.0 stops slower than would otherwise be the case (measured at 400 mm with a D4 camera according to Camera and Imaging Products Association [CIPA] standards; eff ects vary with the photographer and shooting conditions). This increases the range of shutter speeds available and permits hand-held, tripod-free photography in a wide range of situations. Using the Vibration Reduction ON/OFF Switch • Select ON to enable vibration reduction. Vibration reduction is activated when the shutter-release button is pressed halfway, reducing the eff ects of camera shake for improved framing and focus. • Select OFF to turn vibration reduction off . Using the Vibration Reduction Mode Switch The vibration reduction mode switch is used to select the vibration reduction mode when vibration reduction is on. • Select NORMAL to reduce the eff ects of vibration when photographing from a fi xed position and in other situations with comparatively little camera motion. • Select ACTIVE to reduce the eff ects of vibration when shooting from a moving vehicle, while walking, and in other situations with active camera motion. Using Vibration Reduction: Notes • Slide the vibration reduction switch to OFF if the camera does not support vibration reduction. Leaving vibration reduction on may greatly increase the drain on the battery, particularly in the case of Pronea 600i/6i cameras. • When using vibration reduction, press the shutter-release button halfway and wait for the image in the viewfi nder to stabilize before pressing the shutter-release button the rest of the way down. • When vibration reduction is active, the image in the viewfi nder may be blurred after the shutter is released. This does not indicate a malfunction. • Slide the vibration reduction mode switch to NORMAL for panning shots. When the camera is panned, vibration reduction applies only to motion that is not part of the pan (if the camera is panned horizontally, for example, vibration reduction will be applied only to vertical shake), making it much easier to pan the camera smoothly in a wide arc. • Do not turn the camera off or remove the lens while vibration reduction is in eff ect. If power to the lens is cut while vibration reduction is on, the lens may rattle when shaken. This is not a malfunction, and can be corrected by reattaching the lens and turning the camera on. • If the camera is equipped with a built-in fl ash, vibration reduction will be disabled while the fl ash charges. • ON is generally recommended when the camera is mounted on a monopod or a tripod with an unsecured head, although OFF may be preferred depending shooting conditions and the type of tripod. ¦ The Lens Hoo...
Эта инструкция также подходит к моделям:Оптические приборы - AF-S NIKKOR 80-400mm f/4.5-5.6G ED VR (1.01 mb)