Оценок - 2, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Turn the camera off before removing or inserting batteries. To remove the battery, open the battery-chamber cover as described in Step 2, above, and slide the battery out. Note that the battery may become hot during use; observe due caution when removing the battery. Alternative Power Sources To power the camera continuously for extended periods, use an EH-54 AC adapter (available separately; under any circumstances, use another make or model of AC adapter. Failure to observe this precaution could result in overheating or in damage to the camera. Removing the Battery-Chamber Cover To remove the battery-chamber cover when using the optional MB-CP10 battery pack, open the cover, press it down () and twist it off as shown (). Replace the battery-chamber cover when the battery pack is not in use. down while rotating the cover as shown until it clicks into place. 143). Do not, To replace the cover, insert one corner and press Recycle Used Batteries Used batteries are a valuable resource. Please recycle used batteries in accordance with local regulations. First Steps 11 1 2 First Steps 12 The camera stores pictures on CompactFlash™ memory cards. See “Technical Notes: Approved Memory Cards” ( 144) for a list of compatible cards. 1 Turn the camera off 2 Open the memory card slot cover A yellow notice detailing memory card insertion is placed in the memory card slot at shipment. Remove the notice and read the instructions. Inserting Memory Cards 3 Insert a memory card Check that the eject button is all the way down () and then insert a memory card as shown in the label inside the memory card slot cover (). Inserting Memory Cards Insert memory cards terminals fi rst. Inserting the card upside down or backwards could damage the camera or the card. Check to be sure the card is in the correct orientation. 4 Close the memory card slot cover Format Memory Cards Before First Use Memory cards must be formatted before fi rst use. See “The Shooting Menu: CF Card Format” ( 112). Direction of insertion Rear label Terminals DO NOT INSERT: First Steps The Eject Button If the eject button is up when the card-slot cover is closed, closing the cover will partially eject the memory car errors when the camera is turned on. Be sure the eject button is down before inserting memory cards. Removing Memory Cards Memory cards can be removed without loss of data when the camera is off. To remove memory cards, turn the camera off and open the memory card slot cover. Press the eject button to pop it up (), then press it again to partially eject the card (). The card can then be removed by hand. Note that memory cards may become hot during use; observe due caution when removing memory cards. 21The Eject Button If the eject button is up when the card-slot cover is closed, closing the cover will partially eject the memory car errors when the camera is turned on. Be sure the eject button is down before inserting memory cards. Removing Memory Cards Memory cards can be removed without loss of data when the camera is off. To remove memory cards, turn the camera off and open the memory card slot cover. Press the eject button to pop it up (), then press it again to partially eject the card (). The card can then be removed by hand. Note that memory cards may become hot during use; observe due caution when removing memory cards. 21 13 First Steps 14 Turning the Camera On 1 Ready the monitor 2 Turn the camera on The fi rst time the camera is turned on, a languageselection dialog will be displayed ( 15). Choose a language and set the time and date. Turning the Camera Off To turn the camera off, rotate the power switch to the off position. The displays will turn off and the lens will retract. Auto Power Off (Standby Mode) If no operations are performed for one minute (three minutes when menus are displayed), the monitor and electronic viewfi nder will turn off automatically and the camera will enter standby mode, reducing the drain on the batteries (if the camera is powered by an optional AC adapter or the Loop option is selected during a slide show [ 120], the display will turn off after thirty minutes). To reactivate the display, press the , , or button, choose a new mode, or press the shutter-release button halfway. The length of time before the camera enters standby mode can be changed using the Auto off option in the setup menu ( 138). 15 First Steps The Clock Battery When the main battery is installed or an AC adapter is connected, the clock battery will charge in about 10 hours. When fully charged, the clock battery can provide several days of backup power. The clock may be reset when the battery runs low; when the battery is exhausted, the DATE menu is displayed automatically. The Camera Clock The camera clock is less accurate than most watches or household clocks. Check the clock regularly against more accurate timepieces and reset as necessary. † Select No to exit to mode selected with mode dial. If time and date are not set, (“date not set”)...